Appendix: Instrument Configurations and Specifications
Contents
7. Appendix: Instrument Configurations and Specifications¶
7.1. WHOTS-18 300 kHz - Serial 4891¶
[BREAK Wakeup A]
WorkHorse Broadband ADCP Version 50.40
Teledyne RD Instruments (c) 1996-2010
All Rights Reserved.
>ps0
Instrument S/N: 4891
Frequency: 307200 HZ
Configuration: 4 BEAM, JANUS
Match Layer: 10
Beam Angle: 20 DEGREES
Beam Pattern: CONVEX
Orientation: UP
Sensor(s): HEADING TILT 1 TILT 2 TEMPERATURE
Temp Sens Offset: -0.23 degrees C
CPU Firmware: 50.40 [0]
Boot Code Ver: Required: 1.16 Actual: 1.16
DEMOD #1 Ver: ad48, Type: 1f
DEMOD #2 Ver: ad48, Type: 1f
PWRTIMG Ver: 85d3, Type: 5
Board Serial Number Data:
E2 00 00 03 7C 0B 00 09 REC727-1000-04E
63 00 00 03 87 A5 E4 09 CPU727-2000-00J
99 00 00 03 83 DB 8F 09 PIO727-3000-04C
09 00 00 03 40 91 CF 09 DSP727-2001-04G
>ts 22/07/22,23:05:45
>r?
Available Commands:
RE --------------------- Recorder Erase
RF --------------------- Recorder Space used/free (bytes)
RN WHT16 -------------- Set Deployment Name
RR --------------------- Recorder diRectory
RY --------------------- Upload Recorder Files to Host
R? --------------------- Display Recorder Commands
>rf
RF = 69664768,186687488 --- Rec space used (bytes), free (bytes)
>rr
Recorder Directory:
Volume serial number for device #1 is 206f-6241
WHT16000 000 69664768 07-06-21 2:52:36p r a [ 2]
Bytes used on device #1 = 69664768
Total capacity = 256352256 bytes
Total bytes used = 69664768 bytes in 1 files
Total bytes free = 186687488 bytes
>re
Must use 'RE ErAsE' or 're ErAsE' to erase recorder!
Recorder not erased.
>RE ErAsE erasing...
Recorder erased.
>rr
Recorder Directory:
Volume serial number for device #1 is 206f-6241
No files found.
Bytes used on device #1 = 0
Total capacity = 256352256 bytes
Total bytes used = 0 bytes in 0 files
Total bytes free = 256352256 bytes
>rrwht16
Recorder Directory:
Volume serial number for device #1 is 206f-6241
No files found.
Bytes used on device #1 = 0
Total capacity = 256352256 bytes
Total bytes used = 0 bytes in 0 files
Total bytes free = 256352256 bytes
>cf11101
>ps0
Instrument S/N: 4891
Frequency: 307200 HZ
Configuration: 4 BEAM, JANUS
Match Layer: 10
Beam Angle: 20 DEGREES
Beam Pattern: CONVEX
Orientation: UP
Sensor(s): HEADING TILT 1 TILT 2 TEMPERATURE
Temp Sens Offset: -0.23 degrees C
CPU Firmware: 50.40 [0]
Boot Code Ver: Required: 1.16 Actual: 1.16
DEMOD #1 Ver: ad48, Type: 1f
DEMOD #2 Ver: ad48, Type: 1f
PWRTIMG Ver: 85d3, Type: 5
Board Serial Number Data:
E2 00 00 03 7C 0B 00 09 REC727-1000-04E
63 00 00 03 87 A5 E4 09 CPU727-2000-00J
99 00 00 03 83 DB 8F 09 PIO727-3000-04C
09 00 00 03 40 91 CF 09 DSP727-2001-04G
>cf11101
>ea0
>eb0954
>ed1250
>es35
>ex11111
>ez1111101
>wa70
>wb0
>wd111100000
>wf176
>wn30
>wp40
>wv175
>wl2,6
>ws0400
>te00:10:00.00
>tp00:04:00
>tg20220722,23:59:59
>PS0
Instrument S/N: 4891
Frequency: 307200 HZ
Configuration: 4 BEAM, JANUS
Match Layer: 10
Beam Angle: 20 DEGREES
Beam Pattern: CONVEX
Orientation: UP
Sensor(s): HEADING TILT 1 TILT 2 TEMPERATURE
Temp Sens Offset: -0.23 degrees C
CPU Firmware: 50.40 [0]
Boot Code Ver: Required: 1.16 Actual: 1.16
DEMOD #1 Ver: ad48, Type: 1f
DEMOD #2 Ver: ad48, Type: 1f
PWRTIMG Ver: 85d3, Type: 5
Board Serial Number Data:
E2 00 00 03 7C 0B 00 09 REC727-1000-04E
63 00 00 03 87 A5 E4 09 CPU727-2000-00J
99 00 00 03 83 DB 8F 09 PIO727-3000-04C
09 00 00 03 40 91 CF 09 DSP727-2001-04G
>CK
[Parameters saved as USER defaults]
>
7.2. WHOTS-18 600 kHz - Serial 1825¶
[BREAK Wakeup A]
WorkHorse Broadband ADCP Version 51.40
Teledyne RD Instruments (c) 1996-2010
All Rights Reserved.
>
>TS 60/07/22,22:47:44
>?
Available Menus:
DEPLOY? ------------------ Deployment Commands
SYSTEM? ------------------ System Control, Data Recovery and Testing Commands
>SYSTEM
System Control, Data Recovery and Testing Commands:
AC ----------------------- Output Active Fluxgate & Tilt Calibration data
AF ----------------------- Field calibrate to remove hard/soft iron error
AR ----------------------- Restore factory fluxgate calibration data
AX ----------------------- Examine compass performance
AZ ----------------------- Zero pressure reading
CB = 411 ----------------- Serial Port Control (Baud; Par; Stop)
CP # --------------------- Polled Mode (0 = NORMAL, 1 = POLLED)
CZ ---------------------- Power Down Instrument
FC ----------------------- Clear Fault Log
FD ----------------------- Display Fault Log
OL ----------------------- Display Features List
PA ----------------------- Pre-Deployment Tests
PC1 ---------------------- Beam Continuity
PC2 ---------------------- Sensor Data
PS0 ---------------------- System Configuration
PS3 ---------------------- Transformation Matrices
RR ----------------------- Recorder Directory
RF ----------------------- Recorder Space used/free (bytes)
RY ----------------------- Upload Recorder Files to Host
>ol FEATURES
---------------------------------------------------------------------
Feature Installed
---------------------------------------------------------------------
BT-HA (High Accuracy 0.4%) Yes
Water Profile Yes
High Resolution Water Modes No
LADCP/Surface Track/WM15 No
Wave Gauge Acquisition No
Shallow Bottom Mode No
High Rate Pinging No
Narrow Bandwidth only (WB1) No
BT-RA (Reduced Accuracy 1.15%) No
See your technical manual or contact TRDI for information on how to
install additional capability in your WorkHorse.
>p50 ERR 010: UNRECOGNIZED COMMAND
>ps0
Instrument S/N: 1825
Frequency: 614400 HZ
Configuration: 4 BEAM, JANUS
Match Layer: 10
Beam Angle: 20 DEGREES
Beam Pattern: CONVEX
Orientation: UP
Sensor(s): HEADING TILT 1 TILT 2 DEPTH TEMPERATURE PRESSURE
Pressure Sens Coefficients:
c3 = +1.762294E-13
c2 = +3.330826E-08
c1 = +1.389532E-01
Offset = -4.652679E+00
Temp Sens Offset: -0.13 degrees C
CPU Firmware: 51.40 [0]
Boot Code Ver: Required: 1.16 Actual: 1.16
DEMOD #1 Ver: ad48, Type: 1f
DEMOD #2 Ver: ad48, Type: 1f
PWRTIMG Ver: 85d3, Type: 5
Board Serial Number Data:
E4 00 00 02 00 20 C0 09 DSP727-2001-03F
0D 00 00 02 48 A7 98 09 REC727-1000-03A
7E 00 00 02 00 4D 0B 09 PIO727-3000-03C
97 00 00 02 00 3F BB 09 CPU727-2000-00H
>rrwht16
Recorder Directory:
Volume serial number for device #1 is 206f-6241
WHT16000 000 0 09-27-19 0:56:50a r a [ 0]
WHT16001 000 0 09-27-19 2:24:58a r a [ 0]
WHT16002 000 10348242 01-21-20 9:10:02p r a [ 2]
WHT16003 000 11118 01-22-20 0:09:40a r a [ 2529]
WHT16004 000 53628 01-22-20 1:55:24p r a [ 2532]
WHT16005 000 17658 01-22-20 6:31:06p r a [ 2546]
WHT16006 000 7848 01-22-20 8:37:04p r a [ 2551]
WHT16007 000 654 01-22-20 8:53:56p r a [ 2553]
WHT16008 000 7194 01-22-20 10:49:20p r a [ 2554]
WHT16009 000 3924 04-17-20 1:01:30p r a [ 2556]
WHT16010 000 0 04-17-20 1:59:10p r a [ 0]
WHT16011 000 654 04-17-20 2:44:32p r a [ 2557]
WHT16012 000 1962 04-17-20 3:33:42p r a [ 2558]
WHT16013 000 3270 04-17-20 4:47:48p r a [ 2559]
WHT16014 000 0 04-17-20 5:16:56p r a [ 0]
WHT16015 000 1308 04-17-20 6:19:26p r a [ 2560]
WHT16016 000 654 04-17-20 6:51:58p r a [ 2561]
WHT16017 000 2616 04-17-20 7:40:22p r a [ 2562]
WHT16018 000 6540 04-17-20 10:00:42p r a [ 2563]
Bytes used on device #1 = 10467270
Total capacity = 256352256 bytes
Total bytes used = 10467270 bytes in 19 files
Total bytes free = 245854208 bytes
>cf11101
>ea0
>eb0954
>?
Available Menus:
DEPLOY? ------------------ Deployment Commands
SYSTEM? ------------------ System Control, Data Recovery and Testing Commands
>deploy
Deployment Commands:
BP = 000 ----------------- Bottom Track Pings per Ensemble
CF = 11101 --------------- Flow Ctrl (EnsCyc;PngCyc;Binry;Ser;Rec)
CK ----------------------- Keep Parameters as USER Defaults
CR # --------------------- Retrieve Parameters (0 = USER, 1 = FACTORY)
CS ----------------------- Start Deployment
EA = +00000 -------------- Heading Alignment (1/100 deg)
EB = +00954 -------------- Heading Bias (1/100 deg)
ED = 00475 --------------- Transducer Depth (0 - 65535 dm)
ES = 35 ------------------ Salinity (0-40 pp thousand)
EX = 11111 --------------- Coord Transform (Xform: Type,Tilts,3 Bm,Map)
EZ = 1111101 ------------- Sensor Source (C,D,H,P,R,S,T)
RE ----------------------- Recorder ErAsE
RN ----------------------- Set Deployment Name
TE = 00:10:00.00 --------- Time per Ensemble (hrs:min:sec.sec/100)
TF = **/**/**,**:**:** --- Time of First Ping (yr/mon/day,hour:min:sec)
TP = 00:02.00 ------------ Time per Ping (min:sec.sec/100)
TS = 60/07/22,22:50:30 --- Time Set (yr/mon/day,hour:min:sec)
WD = 111 100 000 --------- Data Out (Vel,Cor,Amp; PG,St,P0; P1,P2,P3)
WF = 0088 ---------------- Blank After Transmit (cm)
WN = 025 ----------------- Number of depth cells (1-128)
WP = 00080 --------------- Pings per Ensemble (0-16384)
WS = 0200 ---------------- Depth Cell Size (cm)
WV = 175 ----------------- Mode 1 Ambiguity Vel (cm/s radial)
>RE
Must use 'RE ErAsE' or 're ErAsE' to erase recorder!
Recorder not erased.
>RE ErAsE erasing...
Recorder erased.
>rrwht16
Recorder Directory:
Volume serial number for device #1 is 206f-6241
No files found.
Bytes used on device #1 = 0
Total capacity = 256352256 bytes
Total bytes used = 0 bytes in 0 files
Total bytes free = 256352256 bytes
>cf11101
>ea0
>eb0954
>ed0475
>es35
>ex11111
>ez1111101
>wa70
>wb0
>wd111100000
>wf0088
>wl2,6
>wp80
>ws0200
>wn25
>wv175
>te:00:10:00.00
>tp00:02:00
>tg20220722,23:59:59ERR: TF date/time is more than a year!
ERR: Bad command parameters!Out of range!
>?
Available Menus:
DEPLOY? ------------------ Deployment Commands
SYSTEM? ------------------ System Control, Data Recovery and Testing Commands
>SYSTEM
System Control, Data Recovery and Testing Commands:
AC ----------------------- Output Active Fluxgate & Tilt Calibration data
AF ----------------------- Field calibrate to remove hard/soft iron error
AR ----------------------- Restore factory fluxgate calibration data
AX ----------------------- Examine compass performance
AZ ----------------------- Zero pressure reading
CB = 411 ----------------- Serial Port Control (Baud; Par; Stop)
CP # --------------------- Polled Mode (0 = NORMAL, 1 = POLLED)
CZ ---------------------- Power Down Instrument
FC ----------------------- Clear Fault Log
FD ----------------------- Display Fault Log
OL ----------------------- Display Features List
PA ----------------------- Pre-Deployment Tests
PC1 ---------------------- Beam Continuity
PC2 ---------------------- Sensor Data
PS0 ---------------------- System Configuration
PS3 ---------------------- Transformation Matrices
RR ----------------------- Recorder Directory
RF ----------------------- Recorder Space used/free (bytes)
RY ----------------------- Upload Recorder Files to Host
>PS0
Instrument S/N: 1825
Frequency: 614400 HZ
Configuration: 4 BEAM, JANUS
Match Layer: 10
Beam Angle: 20 DEGREES
Beam Pattern: CONVEX
Orientation: UP
Sensor(s): HEADING TILT 1 TILT 2 DEPTH TEMPERATURE PRESSURE
Pressure Sens Coefficients:
c3 = +1.762294E-13
c2 = +3.330826E-08
c1 = +1.389532E-01
Offset = -4.652679E+00
Temp Sens Offset: -0.13 degrees C
CPU Firmware: 51.40 [0]
Boot Code Ver: Required: 1.16 Actual: 1.16
DEMOD #1 Ver: ad48, Type: 1f
DEMOD #2 Ver: ad48, Type: 1f
PWRTIMG Ver: 85d3, Type: 5
Board Serial Number Data:
E4 00 00 02 00 20 C0 09 DSP727-2001-03F
0D 00 00 02 48 A7 98 09 REC727-1000-03A
7E 00 00 02 00 4D 0B 09 PIO727-3000-03C
97 00 00 02 00 3F BB 09 CPU727-2000-00H
>tg20220722,23:59:59ERR: TF date/time is more than a year!
ERR: Bad command parameters!Out of range!
>tf ERR: Bad command parameters!Out of range!
>TF?
TF **/**/**,**:**:** --- Time of First Ping (yr/mon/day,hour:min:sec)
>TG?
TG ****/**/**,**:**:** - Time of First Ping (CCYY/MM/DD,hh:mm:ss)
>T?
Available Commands:
TB 00:00:00.00 --------- Time per Burst (hrs:min:sec.sec/100)
TC 00000 --------------- Ensembles Per Burst (0-65535)
TE 00:10:00.00 --------- Time per Ensemble (hrs:min:sec.sec/100)
TF **/**/**,**:**:** --- Time of First Ping (yr/mon/day,hour:min:sec)
TG ****/**/**,**:**:** - Time of First Ping (CCYY/MM/DD,hh:mm:ss)
TP 00:02.00 ------------ Time per Ping (min:sec.sec/100)
TS 60/07/22,22:57:03 --- Time Set (yr/mon/day,hour:min:sec)
TT 2060/07/22,22:57:03 - Time Set (CCYY/MM/DD,hh:mm:ss)
TX 00:00:00 ------------ Buffer Output Period: (hh:mm:ss)
T? --------------------- Display Time Help
>TS ERR: Bad command parameters!Out of range!
>
>ts 22/07/22,22:58:00
>tg2022/07/22,23:59:59
>ck?
CK ----------------------- Keep Parameters as USER Defaults
>ck
[Parameters saved as USER defaults]
>ps0
Instrument S/N: 1825
Frequency: 614400 HZ
Configuration: 4 BEAM, JANUS
Match Layer: 10
Beam Angle: 20 DEGREES
Beam Pattern: CONVEX
Orientation: UP
Sensor(s): HEADING TILT 1 TILT 2 DEPTH TEMPERATURE PRESSURE
Pressure Sens Coefficients:
c3 = +1.762294E-13
c2 = +3.330826E-08
c1 = +1.389532E-01
Offset = -4.652679E+00
Temp Sens Offset: -0.13 degrees C
CPU Firmware: 51.40 [0]
Boot Code Ver: Required: 1.16 Actual: 1.16
DEMOD #1 Ver: ad48, Type: 1f
DEMOD #2 Ver: ad48, Type: 1f
PWRTIMG Ver: 85d3, Type: 5
Board Serial Number Data:
E4 00 00 02 00 20 C0 09 DSP727-2001-03F
0D 00 00 02 48 A7 98 09 REC727-1000-03A
7E 00 00 02 00 4D 0B 09 PIO727-3000-03C
97 00 00 02 00 3F BB 09 CPU727-2000-00H
>
===============
[BREAK Wakeup A]
WorkHorse Broadband ADCP Version 51.40
Teledyne RD Instruments (c) 1996-2010
All Rights Reserved.
>ps0
Instrument S/N: 1825
Frequency: 614400 HZ
Configuration: 4 BEAM, JANUS
Match Layer: 10
Beam Angle: 20 DEGREES
Beam Pattern: CONVEX
Orientation: UP
Sensor(s): HEADING TILT 1 TILT 2 DEPTH TEMPERATURE PRESSURE
Pressure Sens Coefficients:
c3 = +1.762294E-13
c2 = +3.330826E-08
c1 = +1.389532E-01
Offset = -4.652679E+00
Temp Sens Offset: -0.13 degrees C
CPU Firmware: 51.40 [0]
Boot Code Ver: Required: 1.16 Actual: 1.16
DEMOD #1 Ver: ad48, Type: 1f
DEMOD #2 Ver: ad48, Type: 1f
PWRTIMG Ver: 85d3, Type: 5
Board Serial Number Data:
E4 00 00 02 00 20 C0 09 DSP727-2001-03F
0D 00 00 02 48 A7 98 09 REC727-1000-03A
7E 00 00 02 00 4D 0B 09 PIO727-3000-03C
97 00 00 02 00 3F BB 09 CPU727-2000-00H
>t?
Available Commands:
TB 00:00:00.00 --------- Time per Burst (hrs:min:sec.sec/100)
TC 00000 --------------- Ensembles Per Burst (0-65535)
TE 00:10:00.00 --------- Time per Ensemble (hrs:min:sec.sec/100)
TF **/**/**,**:**:** --- Time of First Ping (yr/mon/day,hour:min:sec)
TG ****/**/**,**:**:** - Time of First Ping (CCYY/MM/DD,hh:mm:ss)
TP 00:02.00 ------------ Time per Ping (min:sec.sec/100)
TS 22/07/23,00:28:13 --- Time Set (yr/mon/day,hour:min:sec)
TT 2022/07/23,00:28:13 - Time Set (CCYY/MM/DD,hh:mm:ss)
TX 00:00:00 ------------ Buffer Output Period: (hh:mm:ss)
T? --------------------- Display Time Help
>ts220723,00:29:10
>t?
Available Commands:
TB 00:00:00.00 --------- Time per Burst (hrs:min:sec.sec/100)
TC 00000 --------------- Ensembles Per Burst (0-65535)
TE 00:10:00.00 --------- Time per Ensemble (hrs:min:sec.sec/100)
TF **/**/**,**:**:** --- Time of First Ping (yr/mon/day,hour:min:sec)
TG ****/**/**,**:**:** - Time of First Ping (CCYY/MM/DD,hh:mm:ss)
TP 00:02.00 ------------ Time per Ping (min:sec.sec/100)
TS 22/07/23,00:29:13 --- Time Set (yr/mon/day,hour:min:sec)
TT 2022/07/23,00:29:13 - Time Set (CCYY/MM/DD,hh:mm:ss)
TX 00:00:00 ------------ Buffer Output Period: (hh:mm:ss)
T? --------------------- Display Time Help
>tg 2022/07/23,00:40:00
>t?
Available Commands:
TB 00:00:00.00 --------- Time per Burst (hrs:min:sec.sec/100)
TC 00000 --------------- Ensembles Per Burst (0-65535)
TE 00:10:00.00 --------- Time per Ensemble (hrs:min:sec.sec/100)
TF 22/07/23,00:40:00 --- Time of First Ping (yr/mon/day,hour:min:sec)
TG 2022/07/23,00:40:00 - Time of First Ping (CCYY/MM/DD,hh:mm:ss)
TP 00:02.00 ------------ Time per Ping (min:sec.sec/100)
TS 22/07/23,00:29:55 --- Time Set (yr/mon/day,hour:min:sec)
TT 2022/07/23,00:29:55 - Time Set (CCYY/MM/DD,hh:mm:ss)
TX 00:00:00 ------------ Buffer Output Period: (hh:mm:ss)
T? --------------------- Display Time Help
>ck
[Parameters saved as USER defaults]
>deploy?
Deployment Commands:
BP = 000 ----------------- Bottom Track Pings per Ensemble
CF = 11101 --------------- Flow Ctrl (EnsCyc;PngCyc;Binry;Ser;Rec)
CK ----------------------- Keep Parameters as USER Defaults
CR # --------------------- Retrieve Parameters (0 = USER, 1 = FACTORY)
CS ----------------------- Start Deployment
EA = +00000 -------------- Heading Alignment (1/100 deg)
EB = +00954 -------------- Heading Bias (1/100 deg)
ED = 00475 --------------- Transducer Depth (0 - 65535 dm)
ES = 35 ------------------ Salinity (0-40 pp thousand)
EX = 11111 --------------- Coord Transform (Xform: Type,Tilts,3 Bm,Map)
EZ = 1111101 ------------- Sensor Source (C,D,H,P,R,S,T)
RE ----------------------- Recorder ErAsE
RN ----------------------- Set Deployment Name
TE = 00:10:00.00 --------- Time per Ensemble (hrs:min:sec.sec/100)
TF = 22/07/23,00:40:00 --- Time of First Ping (yr/mon/day,hour:min:sec)
TP = 00:02.00 ------------ Time per Ping (min:sec.sec/100)
TS = 22/07/23,00:30:06 --- Time Set (yr/mon/day,hour:min:sec)
WD = 111 100 000 --------- Data Out (Vel,Cor,Amp; PG,St,P0; P1,P2,P3)
WF = 0088 ---------------- Blank After Transmit (cm)
WN = 025 ----------------- Number of depth cells (1-128)
WP = 00080 --------------- Pings per Ensemble (0-16384)
WS = 0200 ---------------- Depth Cell Size (cm)
WV = 175 ----------------- Mode 1 Ambiguity Vel (cm/s radial)
>cs
7.3. WHOTS-18 MicroCAT - Headers¶
# Metadata for Sensor Serial Number: 6411
* <?xml version="1.0"?>
* <!--DeviceManager-->
* <SBEDataUploadFile>
* <ApplicationData>
* <DeviceInterfaceAppData>
* <SoftwareVersion>1.8.2</SoftwareVersion>
* <BuildDate>25-Jul-2018 07:49:42 UTC</BuildDate>
* </DeviceInterfaceAppData>
* </ApplicationData>
* <InstrumentState>
* <StatusData DeviceType='SBE56' SerialNumber='05606411'>
* <DateTime>2023-06-21T20:10:47</DateTime>
* <DelayedStart>2000-01-01T00:00:00</DelayedStart>
* <EventSummary numEvents='0'/>
* <Power>
* <MainSupplyVoltage>3.63</MainSupplyVoltage>
* </Power>
* <ADCRatio>
* <Ratio>11209069</Ratio>
* </ADCRatio>
* <Battery>
* <Installed>2000-01-01T00:00:00</Installed>
* <Samples>480731</Samples>
* </Battery>
* <MemorySummary>
* <Samples>480731</Samples>
* <Bytes>2001408</Bytes>
* <BytesFree>64583168</BytesFree>
* </MemorySummary>
* </StatusData>
*
* <HardwareData DeviceType='SBE56' SerialNumber='05606411'>
* <Manufacturer>Sea-Bird Electronics, Inc</Manufacturer>
* <FirmwareVersion>SBE56 V0.96</FirmwareVersion>
* <FirmwareDate>Feb 25 2011</FirmwareDate>
* <PCBAssembly PCBID='101833' AssemblyNum='41688F'/>
* <MfgDate>Feb 25 2011</MfgDate>
* <PCBType>0</PCBType>
* <InternalSensors>
* <Sensor id='Water Temperature'>
* <type>TEMP0</type>
* <SerialNumber>05606411</SerialNumber>
* </Sensor>
* </InternalSensors>
* </HardwareData>
*
* <ConfigurationData DeviceType='SBE56' SerialNumber='05606411'>
* <Settings
* samplePeriod='60' format='1' />
* </ConfigurationData>
*
* <CalibrationCoefficients DeviceType='SBE56' SerialNumber='05606411'>
* <Calibration format='TEMP0' id='Water Temperature'>
* <CalDate>2016-03-11</CalDate>
* <a0>-1.251684E-03</a0>
* <a1>3.519107E-04</a1>
* <a2>-7.014985E-06</a2>
* <a3>2.081770E-07</a3>
* <OFFSET>0.000000E+00</OFFSET>
* </Calibration>
* </CalibrationCoefficients>
*
* <EventSummary DeviceType='SBE56' SerialNumber='05606411'>
* <EventList numEvents='0' maxStack='-2'>
* </EventList>
* </EventSummary>
*
* </InstrumentState>
# nquan = 4
# nvalues = 480731
# units = specified
# name 0 = scan: Scan Count
# name 1 = timeJ: Julian Days
# name 2 = t090C: Temperature [ITS-90, deg C
# name 3 = flag: 0.000e+00
# span 0 = 1, 480731
# span 1 = 203.999306, 537.839572
# span 2 = -0.0022, 46.7334
# span 3 = 0.000e+00, 0.000e+00
# interval = seconds: 60
# start_time = Jul 22 2022 23:59:00
# bad_flag = -9.990e-29
# sensor 0 = RRatio temperature, 05606411
# datcnv_date = Jun 21 2023 20:34:29, SeatermUSB v 1.8.2
# datcnv_in = C:\Users\Rtgra\Documents\Buoy Systems\ORS\WHOTS\W18\DATA\SUBSURFACE\SBE56_6411.xml
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 7213
* <?xml version="1.0"?>
* <!--DeviceManager-->
* <SBEDataUploadFile>
* <ApplicationData>
* <DeviceInterfaceAppData>
* <SoftwareVersion>1.8.2</SoftwareVersion>
* <BuildDate>25-Jul-2018 07:49:42 UTC</BuildDate>
* </DeviceInterfaceAppData>
* </ApplicationData>
* <InstrumentState>
* <StatusData DeviceType='SBE56' SerialNumber='05607213'>
* <DateTime>2023-06-21T20:21:02</DateTime>
* <DelayedStart>2000-01-01T00:00:00</DelayedStart>
* <EventSummary numEvents='0'/>
* <Power>
* <MainSupplyVoltage>3.65</MainSupplyVoltage>
* </Power>
* <ADCRatio>
* <Ratio>9651696</Ratio>
* </ADCRatio>
* <Battery>
* <Installed>2000-01-01T00:00:00</Installed>
* <Samples>480741</Samples>
* </Battery>
* <MemorySummary>
* <Samples>480741</Samples>
* <Bytes>2001408</Bytes>
* <BytesFree>64583168</BytesFree>
* </MemorySummary>
* </StatusData>
*
* <HardwareData DeviceType='SBE56' SerialNumber='05607213'>
* <Manufacturer>Sea-Bird Electronics, Inc</Manufacturer>
* <FirmwareVersion>SBE56 V0.96</FirmwareVersion>
* <FirmwareDate>Feb 25 2011</FirmwareDate>
* <PCBAssembly PCBID='112208' AssemblyNum='41688F'/>
* <MfgDate>Feb 25 2011</MfgDate>
* <PCBType>0</PCBType>
* <InternalSensors>
* <Sensor id='Water Temperature'>
* <type>TEMP0</type>
* <SerialNumber>05607213</SerialNumber>
* </Sensor>
* </InternalSensors>
* </HardwareData>
*
* <ConfigurationData DeviceType='SBE56' SerialNumber='05607213'>
* <Settings
* samplePeriod='60' format='1' />
* </ConfigurationData>
*
* <CalibrationCoefficients DeviceType='SBE56' SerialNumber='05607213'>
* <Calibration format='TEMP0' id='Water Temperature'>
* <CalDate>2016-12-06</CalDate>
* <a0>-1.412968E-03</a0>
* <a1>3.625611E-04</a1>
* <a2>-7.149116E-06</a2>
* <a3>2.145689E-07</a3>
* <OFFSET>0.000000E+00</OFFSET>
* </Calibration>
* </CalibrationCoefficients>
*
* <EventSummary DeviceType='SBE56' SerialNumber='05607213'>
* <EventList numEvents='0' maxStack='-2'>
* </EventList>
* </EventSummary>
*
* </InstrumentState>
# nquan = 4
# nvalues = 480741
# units = specified
# name 0 = scan: Scan Count
# name 1 = timeJ: Julian Days
# name 2 = t090C: Temperature [ITS-90, deg C
# name 3 = flag: 0.000e+00
# span 0 = 1, 480741
# span 1 = 203.999306, 537.846516
# span 2 = -0.0016, 49.6870
# span 3 = 0.000e+00, 0.000e+00
# interval = seconds: 60
# start_time = Jul 22 2022 23:59:00
# bad_flag = -9.990e-29
# sensor 0 = RRatio temperature, 05607213
# datcnv_date = Jun 21 2023 20:35:06, SeatermUSB v 1.8.2
# datcnv_in = C:\Users\Rtgra\Documents\Buoy Systems\ORS\WHOTS\W18\DATA\SUBSURFACE\SBE56_7213.xml
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 7214
* <?xml version="1.0"?>
* <!--DeviceManager-->
* <SBEDataUploadFile>
* <ApplicationData>
* <DeviceInterfaceAppData>
* <SoftwareVersion>1.8.2</SoftwareVersion>
* <BuildDate>25-Jul-2018 07:49:42 UTC</BuildDate>
* </DeviceInterfaceAppData>
* </ApplicationData>
* <InstrumentState>
* <StatusData DeviceType='SBE56' SerialNumber='05607214'>
* <DateTime>2023-06-21T20:26:25</DateTime>
* <DelayedStart>2000-01-01T00:00:00</DelayedStart>
* <EventSummary numEvents='0'/>
* <Power>
* <MainSupplyVoltage>3.65</MainSupplyVoltage>
* </Power>
* <ADCRatio>
* <Ratio>8790379</Ratio>
* </ADCRatio>
* <Battery>
* <Installed>2000-01-01T00:00:00</Installed>
* <Samples>480747</Samples>
* </Battery>
* <MemorySummary>
* <Samples>480747</Samples>
* <Bytes>2001408</Bytes>
* <BytesFree>64583168</BytesFree>
* </MemorySummary>
* </StatusData>
*
* <HardwareData DeviceType='SBE56' SerialNumber='05607214'>
* <Manufacturer>Sea-Bird Electronics, Inc</Manufacturer>
* <FirmwareVersion>SBE56 V0.96</FirmwareVersion>
* <FirmwareDate>Feb 25 2011</FirmwareDate>
* <PCBAssembly PCBID='112199' AssemblyNum='41688F'/>
* <MfgDate>Feb 25 2011</MfgDate>
* <PCBType>0</PCBType>
* <InternalSensors>
* <Sensor id='Water Temperature'>
* <type>TEMP0</type>
* <SerialNumber>05607214</SerialNumber>
* </Sensor>
* </InternalSensors>
* </HardwareData>
*
* <ConfigurationData DeviceType='SBE56' SerialNumber='05607214'>
* <Settings
* samplePeriod='60' format='1' />
* </ConfigurationData>
*
* <CalibrationCoefficients DeviceType='SBE56' SerialNumber='05607214'>
* <Calibration format='TEMP0' id='Water Temperature'>
* <CalDate>2022-02-22</CalDate>
* <a0>-1.404439E-03</a0>
* <a1>3.594089E-04</a1>
* <a2>-6.928444E-06</a2>
* <a3>2.100205E-07</a3>
* <OFFSET>0.000000E+00</OFFSET>
* </Calibration>
* </CalibrationCoefficients>
*
* <EventSummary DeviceType='SBE56' SerialNumber='05607214'>
* <EventList numEvents='0' maxStack='-2'>
* </EventList>
* </EventSummary>
*
* </InstrumentState>
# nquan = 4
# nvalues = 480747
# units = specified
# name 0 = scan: Scan Count
# name 1 = timeJ: Julian Days
# name 2 = t090C: Temperature [ITS-90, deg C
# name 3 = flag: 0.000e+00
# span 0 = 1, 480747
# span 1 = 203.999306, 537.850683
# span 2 = -0.0040, 44.2721
# span 3 = 0.000e+00, 0.000e+00
# interval = seconds: 60
# start_time = Jul 22 2022 23:59:00
# bad_flag = -9.990e-29
# sensor 0 = RRatio temperature, 05607214
# datcnv_date = Jun 21 2023 20:35:19, SeatermUSB v 1.8.2
# datcnv_in = C:\Users\Rtgra\Documents\Buoy Systems\ORS\WHOTS\W18\DATA\SUBSURFACE\SBE56_7214.xml
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 7215
* <?xml version="1.0"?>
* <!--DeviceManager-->
* <SBEDataUploadFile>
* <ApplicationData>
* <DeviceInterfaceAppData>
* <SoftwareVersion>1.8.2</SoftwareVersion>
* <BuildDate>25-Jul-2018 07:49:42 UTC</BuildDate>
* </DeviceInterfaceAppData>
* </ApplicationData>
* <InstrumentState>
* <StatusData DeviceType='SBE56' SerialNumber='05607215'>
* <DateTime>2023-06-21T20:29:55</DateTime>
* <DelayedStart>2000-01-01T00:00:00</DelayedStart>
* <EventSummary numEvents='0'/>
* <Power>
* <MainSupplyVoltage>3.63</MainSupplyVoltage>
* </Power>
* <ADCRatio>
* <Ratio>8856121</Ratio>
* </ADCRatio>
* <Battery>
* <Installed>2000-01-01T00:00:00</Installed>
* <Samples>480750</Samples>
* </Battery>
* <MemorySummary>
* <Samples>480750</Samples>
* <Bytes>2001408</Bytes>
* <BytesFree>64583168</BytesFree>
* </MemorySummary>
* </StatusData>
*
* <HardwareData DeviceType='SBE56' SerialNumber='05607215'>
* <Manufacturer>Sea-Bird Electronics, Inc</Manufacturer>
* <FirmwareVersion>SBE56 V0.96</FirmwareVersion>
* <FirmwareDate>Feb 25 2011</FirmwareDate>
* <PCBAssembly PCBID='112209' AssemblyNum='41688F'/>
* <MfgDate>Feb 25 2011</MfgDate>
* <PCBType>0</PCBType>
* <InternalSensors>
* <Sensor id='Water Temperature'>
* <type>TEMP0</type>
* <SerialNumber>05607215</SerialNumber>
* </Sensor>
* </InternalSensors>
* </HardwareData>
*
* <ConfigurationData DeviceType='SBE56' SerialNumber='05607215'>
* <Settings
* samplePeriod='60' format='1' />
* </ConfigurationData>
*
* <CalibrationCoefficients DeviceType='SBE56' SerialNumber='05607215'>
* <Calibration format='TEMP0' id='Water Temperature'>
* <CalDate>2022-02-18</CalDate>
* <a0>-1.447522E-03</a0>
* <a1>3.705846E-04</a1>
* <a2>-7.702980E-06</a2>
* <a3>2.256575E-07</a3>
* <OFFSET>0.000000E+00</OFFSET>
* </Calibration>
* </CalibrationCoefficients>
*
* <EventSummary DeviceType='SBE56' SerialNumber='05607215'>
* <EventList numEvents='0' maxStack='-2'>
* </EventList>
* </EventSummary>
*
* </InstrumentState>
# nquan = 4
# nvalues = 480750
# units = specified
# name 0 = scan: Scan Count
# name 1 = timeJ: Julian Days
# name 2 = t090C: Temperature [ITS-90, deg C
# name 3 = flag: 0.000e+00
# span 0 = 1, 480750
# span 1 = 203.999306, 537.852766
# span 2 = -0.0023, 45.8691
# span 3 = 0.000e+00, 0.000e+00
# interval = seconds: 60
# start_time = Jul 22 2022 23:59:00
# bad_flag = -9.990e-29
# sensor 0 = RRatio temperature, 05607215
# datcnv_date = Jun 21 2023 20:35:30, SeatermUSB v 1.8.2
# datcnv_in = C:\Users\Rtgra\Documents\Buoy Systems\ORS\WHOTS\W18\DATA\SUBSURFACE\SBE56_7215.xml
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 7212
* <?xml version="1.0"?>
* <!--DeviceManager-->
* <SBEDataUploadFile>
* <ApplicationData>
* <DeviceInterfaceAppData>
* <SoftwareVersion>1.8.2</SoftwareVersion>
* <BuildDate>25-Jul-2018 07:49:42 UTC</BuildDate>
* </DeviceInterfaceAppData>
* </ApplicationData>
* <InstrumentState>
* <StatusData DeviceType='SBE56' SerialNumber='05607212'>
* <DateTime>2023-06-21T20:16:15</DateTime>
* <DelayedStart>2000-01-01T00:00:00</DelayedStart>
* <EventSummary numEvents='255'/>
* <Power>
* <MainSupplyVoltage>3.65</MainSupplyVoltage>
* </Power>
* <ADCRatio>
* <Ratio>1003343</Ratio>
* </ADCRatio>
* <Battery>
* <Installed>2000-01-01T00:00:00</Installed>
* <Samples>480736</Samples>
* </Battery>
* <MemorySummary>
* <Samples>480736</Samples>
* <Bytes>2001408</Bytes>
* <BytesFree>64583168</BytesFree>
* </MemorySummary>
* </StatusData>
*
* <HardwareData DeviceType='SBE56' SerialNumber='05607212'>
* <Manufacturer>Sea-Bird Electronics, Inc</Manufacturer>
* <FirmwareVersion>SBE56 V0.96</FirmwareVersion>
* <FirmwareDate>Feb 25 2011</FirmwareDate>
* <PCBAssembly PCBID='112207' AssemblyNum='41688F'/>
* <MfgDate>Feb 25 2011</MfgDate>
* <PCBType>0</PCBType>
* <InternalSensors>
* <Sensor id='Water Temperature'>
* <type>TEMP0</type>
* <SerialNumber>05607212</SerialNumber>
* </Sensor>
* </InternalSensors>
* </HardwareData>
*
* <ConfigurationData DeviceType='SBE56' SerialNumber='05607212'>
* <Settings
* samplePeriod='60' format='1' />
* </ConfigurationData>
*
* <CalibrationCoefficients DeviceType='SBE56' SerialNumber='05607212'>
* <Calibration format='TEMP0' id='Water Temperature'>
* <CalDate>2022-02-18</CalDate>
* <a0>-1.418179E-03</a0>
* <a1>3.633361E-04</a1>
* <a2>-7.201988E-06</a2>
* <a3>2.156908E-07</a3>
* <OFFSET>0.000000E+00</OFFSET>
* </Calibration>
* </CalibrationCoefficients>
*
* <EventSummary DeviceType='SBE56' SerialNumber='05607212'>
* <EventList numEvents='255' maxStack='-2'>
* <Event type='Error11' count='255'/>
* </EventList>
* </EventSummary>
*
* </InstrumentState>
* <UserHeaderInsert>
* <![CDATA[
* ** BROKEN PROBE/GUARD
* ]]>
* </UserHeaderInsert>
# nquan = 4
# nvalues = 480736
# units = specified
# name 0 = scan: Scan Count
# name 1 = timeJ: Julian Days
# name 2 = t090C: Temperature [ITS-90, deg C
# name 3 = flag: 0.000e+00
# span 0 = 1, 480736
# span 1 = 203.999306, 537.843044
# span 2 = -0.0029, 42.5076
# span 3 = 0.000e+00, 0.000e+00
# interval = seconds: 60
# start_time = Jul 22 2022 23:59:00
# bad_flag = -9.990e-29
# sensor 0 = RRatio temperature, 05607212
# datcnv_date = Jun 21 2023 20:34:54, SeatermUSB v 1.8.2
# datcnv_in = C:\Users\Rtgra\Documents\Buoy Systems\ORS\WHOTS\W18\DATA\SUBSURFACE\SBE56_7212.xml
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 1834
* Sea-Bird SBE37 Data File:
* FileName = C:\Users\Rtgra\Documents\Buoy Systems\ORS\WHOTS\W18\DATA\SURFACE\SBE37_SST_1834.asc
* Software Version 1.59
* Temperature SN = 1834
* Conductivity SN = 1834
* System UpLoad Time = Jun 21 2023 02:56:46
** WHOTS 18 SYSTEM 1 SST SN1834
* ds
* 1ds
* SBE37-SM 485 V 2.3b SERIAL NO. 1834 21 Jun 2023 02:55:47
* not logging: received stop command
* sample interval = 300 seconds
* samplenumber = 96600, free = 136416
* store time with each sample
* do not output salinity with each sample
* do not output sound velocity with each sample
* reference pressure = 0.0 db
* do not output density with each sample
* do not output depth with each sample
* A/D cycles to average = 4
* internal pump not installed
* temperature = 23.41 deg C
* S>
* 1dc
* SBE37-SM 485 V 2.3b 1834
* temperature: 04-mar-22
* TA0 = 9.598777e-06
* TA1 = 2.755003e-04
* TA2 = -2.262447e-06
* TA3 = 1.566359e-07
* conductivity: 04-mar-22
* G = -1.011899e+00
* H = 1.395489e-01
* I = -1.084226e-04
* J = 3.021298e-05
* CPCOR = -9.570000e-08
* CTCOR = 3.250000e-06
* WBOTC = -6.124698e-06
* rtc: 04-mar-22
* RTCA0 = 1.000004e+00
* RTCA1 = 1.583139e-06
* RTCA2 = -3.071189e-08
* S>
*END*
# Metadata for Sensor Serial Number: 3617
* Sea-Bird SBE37 Data File:
* FileName = C:\Users\Jefrey\Documents\WHOTS-19\w19_07m_3617_data_2ndtry.asc
* Software Version 1.59
* Temperature SN = 3617
* Conductivity SN = 3617
* System UpLoad Time = Jun 26 2023 20:16:43
** WHOTS-18
** 7m
* ds
* SBE37-SM V 2.6b SERIAL NO. 3617 06-26-2023 20:15:22
* not logging: received stop command
* sample interval = 180 seconds
* samplenumber = 160144, free = 72872
* do not transmit real-time data
* output salinity with each sample
* do not output sound velocity with each sample
* store time with each sample
* number of samples to average = 4
* reference pressure = 7.0 db
* serial sync mode disabled
* wait time after serial sync sampling = 30 seconds
* internal pump not installed
* temperature = 21.56 deg C
* S>
* SBE37-SM V 2.6b 3617
* temperature: 17-nov-21
* TA0 = -2.196350e-04
* TA1 = 3.113773e-04
* TA2 = -4.679920e-06
* TA3 = 2.107474e-07
* conductivity: 17-nov-21
* G = -1.022418e+00
* H = 1.462615e-01
* I = -8.351268e-05
* J = 3.152163e-05
* CPCOR = -9.570000e-08
* CTCOR = 3.250000e-06
* WBOTC = -1.710719e-05
* rtc: 17-nov-21
* RTCA0 = 9.999822e-01
* RTCA1 = 1.686235e-06
* RTCA2 = -3.276656e-08
* S>
*END*
# Metadata for Sensor Serial Number: 6893
* Sea-Bird SBE37SM-RS232 Data File:
* FileName = D:\WHOTS-18_mcat_recovery\w18_15m_6893_data.hex
* Software version SeatermV2 2.8.0.119
* Temperature SN = 6893
* Conductivity SN = 6893
* System UpLoad Time = Jun 21 2023 19:25:35
* sample interval = 60 seconds
* <ApplicationData>
* <Seaterm232>
* <SoftwareVersion>2.8.0.119</SoftwareVersion>
* <BuildDate>07-Nov-2018</BuildDate>
* </Seaterm232>
* </ApplicationData>
* <InstrumentState>
* <HardwareData DeviceType='SBE37SM-RS232' SerialNumber='03706893'>
*
* <Manufacturer>Sea-Bird Electronics, Inc.</Manufacturer>
*
* <FirmwareVersion>3.1</FirmwareVersion>
*
* <FirmwareDate>Jan 20 2012 17:33:01</FirmwareDate>
*
* <PCBAssembly>41647</PCBAssembly>
*
* <PCBAssembly>41624A</PCBAssembly>
*
* <PCBAssembly>41611D</PCBAssembly>
*
* <MfgDate>17 Mar 2009</MfgDate>
*
* <FirmwareLoader>SBE 37 FirmwareLoader V 1.0</FirmwareLoader>
*
* <InternalSensors>
*
* <Sensor id='Temperature'>
*
* <type>temperature-1</type>
*
* <SerialNumber>03706893</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Conductivity'>
*
* <type>conductivity-1</type>
*
* <SerialNumber>03706893</SerialNumber>
*
* </Sensor>
*
* </InternalSensors>
*
* </HardwareData>
* <StatusData DeviceType='SBE37SM-RS232' SerialNumber='03706893'>
*
* <DateTime>2023-06-21T18:38:28</DateTime>
*
* <EventSummary numEvents='7'/>
*
* <Power>
*
* <vMain> 6.93</vMain>
*
* <vLith> 3.18</vLith>
*
* </Power>
*
* <MemorySummary>
*
* <Bytes>4806370</Bytes>
*
* <Samples>480637</Samples>
*
* <SamplesFree>358223</SamplesFree>
*
* <SampleLength>10</SampleLength>
*
* </MemorySummary>
*
* <AutonomousSampling>no, stop command</AutonomousSampling>
*
* </StatusData>
* <ConfigurationData DeviceType='SBE37SM-RS232' SerialNumber='03706893'>
*
* <PressureInstalled>no</PressureInstalled>
*
* <ReferencePressure>1.500000e+01</ReferencePressure>
*
* <PumpInstalled>no</PumpInstalled>
*
* <SampleDataFormat>converted engineering alternate</SampleDataFormat>
*
* <OutputSalinity>yes</OutputSalinity>
*
* <OutputSV>no</OutputSV>
*
* <TxRealTime>no</TxRealTime>
*
* <SampleInterval>60</SampleInterval>
*
* <SyncMode>no</SyncMode>
*
* </ConfigurationData>
* <CalibrationCoefficients DeviceType='SBE37SM-RS232' SerialNumber='03706893'>
*
* <Calibration format='TEMP1' id='Temperature'>
*
* <SerialNum>03706893</SerialNum>
*
* <CalDate>13-Nov-21</CalDate>
*
* <A0>7.877624e-05</A0>
*
* <A1>2.703790e-04</A1>
*
* <A2>-2.165396e-06</A2>
*
* <A3>1.442060e-07</A3>
*
* </Calibration>
*
* <Calibration format='WBCOND0' id='Conductivity'>
*
* <SerialNum>03706893</SerialNum>
*
* <CalDate>13-Nov-21</CalDate>
*
* <G>-1.028597e+00</G>
*
* <H>1.583802e-01</H>
*
* <I>-3.384380e-04</I>
*
* <J>5.093549e-05</J>
*
* <PCOR>-9.570000e-08</PCOR>
*
* <TCOR>3.250000e-06</TCOR>
*
* <WBOTC>2.611541e-07</WBOTC>
*
* </Calibration>
*
* </CalibrationCoefficients>
* <EventCounters DeviceType='SBE37SM-RS232' SerialNumber='03706893'>
*
* <EventSummary numEvents='7'/>
*
* <Event type='PON reset' count='7'/>
*
* </EventCounters></InstrumentState>
* <UserHeaderInsert>
* <![CDATA[
** WHOTS-18
** 15m
* ]]>
* </UserHeaderInsert>
# nquan = 5
# nvalues = 480637
# units = specified
# name 0 = cond0S/m: Conductivity [S/m]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = prM: Pressure [db]
# name 3 = timeJV2: Time, Instrument [julian days]
# name 4 = flag: 0.000e+00
# span 0 = -0.000011, 5.609118
# span 1 = 0.0273, 31.9968
# span 2 = 15.000, 15.000
# span 3 = 204.000000, 537.775000
# span 4 = 0.0000e+00, 0.0000e+00
# interval = seconds: 60
# start_time = Jul 23 2022 00:00:00 [Instrument's time stamp, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="2" >
# <sensor Channel="1" >
# <!-- Count, Temperature -->
# <TemperatureSensor SensorID="58" >
# <SerialNumber>6893</SerialNumber>
# <CalibrationDate>13-Nov-21</CalibrationDate>
# <A0>7.87762400e-005</A0>
# <A1>2.70379000e-004</A1>
# <A2>-2.16539600e-006</A2>
# <A3>1.44206000e-007</A3>
# <Slope>1.00000000</Slope>
# <Offset>0.0000</Offset>
# </TemperatureSensor>
# </sensor>
# <sensor Channel="2" >
# <!-- Frequency 0, Conductivity -->
# <ConductivitySensor SensorID="3" >
# <SerialNumber>6893</SerialNumber>
# <CalibrationDate>13-Nov-21</CalibrationDate>
# <UseG_J>1</UseG_J>
# <!-- Cell const and series R are applicable only for wide range sensors. -->
# <SeriesR>0.0000</SeriesR>
# <CellConst>2000.0000</CellConst>
# <ConductivityType>1</ConductivityType>
# <Coefficients equation="0" >
# <A>0.00000000e+000</A>
# <B>0.00000000e+000</B>
# <C>0.00000000e+000</C>
# <D>0.00000000e+000</D>
# <M>0.0</M>
# <CPcor>-9.57000000e-008</CPcor>
# </Coefficients>
# <Coefficients equation="1" >
# <G>-1.02859700e+000</G>
# <H>1.58380200e-001</H>
# <I>-3.38438000e-004</I>
# <J>5.09354900e-005</J>
# <CPcor>-9.57000000e-008</CPcor>
# <CTcor>3.2500e-006</CTcor>
# <!-- WBOTC not applicable unless ConductivityType = 1. -->
# <WBOTC>2.61154100e-007</WBOTC>
# </Coefficients>
# <Slope>1.00000000</Slope>
# <Offset>0.00000</Offset>
# </ConductivitySensor>
# </sensor>
# </Sensors>
# datcnv_date = Jun 22 2023 14:25:14, 7.26.7.129 [datcnv_vars = 4]
# datcnv_in = C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_15m_6893_data.hex C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_15m_6893_data.xmlcon
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 6894
* Sea-Bird SBE37SM-RS232 Data File:
* FileName = C:\Users\Jefrey\Documents\WHOTS-18_mcat_recovery\w18_25m_6894_data.hex
* Software version SeatermV2 2.8.0.119
* Temperature SN = 6894
* Conductivity SN = 6894
* System UpLoad Time = Jun 21 2023 20:39:31
* sample interval = 60 seconds
* <ApplicationData>
* <Seaterm232>
* <SoftwareVersion>2.8.0.119</SoftwareVersion>
* <BuildDate>07-Nov-2018</BuildDate>
* </Seaterm232>
* </ApplicationData>
* <InstrumentState>
* <HardwareData DeviceType='SBE37SM-RS232' SerialNumber='03706894'>
*
* <Manufacturer>Sea-Bird Electronics, Inc.</Manufacturer>
*
* <FirmwareVersion>3.1</FirmwareVersion>
*
* <FirmwareDate>Jan 20 2012 17:33:01</FirmwareDate>
*
* <PCBAssembly>41647</PCBAssembly>
*
* <PCBAssembly>41624A</PCBAssembly>
*
* <PCBAssembly>41611D</PCBAssembly>
*
* <MfgDate>17 Mar 2009</MfgDate>
*
* <FirmwareLoader>SBE 37 FirmwareLoader V 1.0</FirmwareLoader>
*
* <InternalSensors>
*
* <Sensor id='Temperature'>
*
* <type>temperature-1</type>
*
* <SerialNumber>03706894</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Conductivity'>
*
* <type>conductivity-1</type>
*
* <SerialNumber>03706894</SerialNumber>
*
* </Sensor>
*
* </InternalSensors>
*
* </HardwareData>
* <StatusData DeviceType='SBE37SM-RS232' SerialNumber='03706894'>
*
* <DateTime>2023-06-21T19:19:43</DateTime>
*
* <EventSummary numEvents='5'/>
*
* <Power>
*
* <vMain> 6.99</vMain>
*
* <vLith> 3.18</vLith>
*
* </Power>
*
* <MemorySummary>
*
* <Bytes>4806790</Bytes>
*
* <Samples>480679</Samples>
*
* <SamplesFree>358181</SamplesFree>
*
* <SampleLength>10</SampleLength>
*
* </MemorySummary>
*
* <AutonomousSampling>no, stop command</AutonomousSampling>
*
* </StatusData>
* <ConfigurationData DeviceType='SBE37SM-RS232' SerialNumber='03706894'>
*
* <PressureInstalled>no</PressureInstalled>
*
* <ReferencePressure>2.500000e+01</ReferencePressure>
*
* <PumpInstalled>no</PumpInstalled>
*
* <SampleDataFormat>converted engineering</SampleDataFormat>
*
* <OutputSalinity>yes</OutputSalinity>
*
* <OutputSV>no</OutputSV>
*
* <TxRealTime>no</TxRealTime>
*
* <SampleInterval>60</SampleInterval>
*
* <SyncMode>no</SyncMode>
*
* </ConfigurationData>
* <CalibrationCoefficients DeviceType='SBE37SM-RS232' SerialNumber='03706894'>
*
* <Calibration format='TEMP1' id='Temperature'>
*
* <SerialNum>03706894</SerialNum>
*
* <CalDate>04-Nov-21</CalDate>
*
* <A0>4.355702e-05</A0>
*
* <A1>2.764020e-04</A1>
*
* <A2>-2.643107e-06</A2>
*
* <A3>1.560671e-07</A3>
*
* </Calibration>
*
* <Calibration format='WBCOND0' id='Conductivity'>
*
* <SerialNum>03706894</SerialNum>
*
* <CalDate>04-Nov-21</CalDate>
*
* <G>-1.002938e+00</G>
*
* <H>1.441178e-01</H>
*
* <I>-4.697682e-04</I>
*
* <J>5.762839e-05</J>
*
* <PCOR>-9.570000e-08</PCOR>
*
* <TCOR>3.250000e-06</TCOR>
*
* <WBOTC>-3.464574e-07</WBOTC>
*
* </Calibration>
*
* </CalibrationCoefficients>
* <EventCounters DeviceType='SBE37SM-RS232' SerialNumber='03706894'>
*
* <EventSummary numEvents='5'/>
*
* <Event type='PON reset' count='5'/>
*
* </EventCounters></InstrumentState>
* <UserHeaderInsert>
* <![CDATA[
** WHOTS18 WHOTS18
** 55m 25m
* ]]>
* </UserHeaderInsert>
# nquan = 5
# nvalues = 480679
# units = specified
# name 0 = cond0S/m: Conductivity [S/m]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = prM: Pressure [db]
# name 3 = timeJV2: Time, Instrument [julian days]
# name 4 = flag: 0.000e+00
# span 0 = -0.000031, 5.612718
# span 1 = 0.0847, 32.2924
# span 2 = 25.000, 25.000
# span 3 = 204.000000, 537.804167
# span 4 = 0.0000e+00, 0.0000e+00
# interval = seconds: 60
# start_time = Jul 23 2022 00:00:00 [Instrument's time stamp, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="2" >
# <sensor Channel="1" >
# <!-- Count, Temperature -->
# <TemperatureSensor SensorID="58" >
# <SerialNumber>6894</SerialNumber>
# <CalibrationDate>04-Nov-21</CalibrationDate>
# <A0>4.35570200e-005</A0>
# <A1>2.76402000e-004</A1>
# <A2>-2.64310700e-006</A2>
# <A3>1.56067100e-007</A3>
# <Slope>1.00000000</Slope>
# <Offset>0.0000</Offset>
# </TemperatureSensor>
# </sensor>
# <sensor Channel="2" >
# <!-- Frequency 0, Conductivity -->
# <ConductivitySensor SensorID="3" >
# <SerialNumber>6894</SerialNumber>
# <CalibrationDate>04-Nov-21</CalibrationDate>
# <UseG_J>1</UseG_J>
# <!-- Cell const and series R are applicable only for wide range sensors. -->
# <SeriesR>0.0000</SeriesR>
# <CellConst>2000.0000</CellConst>
# <ConductivityType>1</ConductivityType>
# <Coefficients equation="0" >
# <A>0.00000000e+000</A>
# <B>0.00000000e+000</B>
# <C>0.00000000e+000</C>
# <D>0.00000000e+000</D>
# <M>0.0</M>
# <CPcor>-9.57000000e-008</CPcor>
# </Coefficients>
# <Coefficients equation="1" >
# <G>-1.00293800e+000</G>
# <H>1.44117800e-001</H>
# <I>-4.69768200e-004</I>
# <J>5.76283900e-005</J>
# <CPcor>-9.57000000e-008</CPcor>
# <CTcor>3.2500e-006</CTcor>
# <!-- WBOTC not applicable unless ConductivityType = 1. -->
# <WBOTC>-3.46457400e-007</WBOTC>
# </Coefficients>
# <Slope>1.00000000</Slope>
# <Offset>0.00000</Offset>
# </ConductivitySensor>
# </sensor>
# </Sensors>
# datcnv_date = Jun 22 2023 14:30:17, 7.26.7.129 [datcnv_vars = 4]
# datcnv_in = C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_25m_6894_data.hex C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_25m_6894_data.xmlcon
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 6896
* Sea-Bird SBE37SM-RS232 Data File:
* FileName = C:\Users\Jefrey\Documents\WHOTS-18_mcat_recovery\w18_40m_6896_data.hex
* Software version SeatermV2 2.8.0.119
* Temperature SN = 6896
* Conductivity SN = 6896
* System UpLoad Time = Jun 21 2023 22:13:54
* sample interval = 60 seconds
* <ApplicationData>
* <Seaterm232>
* <SoftwareVersion>2.8.0.119</SoftwareVersion>
* <BuildDate>07-Nov-2018</BuildDate>
* </Seaterm232>
* </ApplicationData>
* <InstrumentState>
* <HardwareData DeviceType='SBE37SM-RS232' SerialNumber='03706896'>
*
* <Manufacturer>Sea-Bird Electronics, Inc.</Manufacturer>
*
* <FirmwareVersion>3.1</FirmwareVersion>
*
* <FirmwareDate>Jan 20 2012 17:33:01</FirmwareDate>
*
* <PCBAssembly>41647</PCBAssembly>
*
* <PCBAssembly>41624A</PCBAssembly>
*
* <PCBAssembly>41611D</PCBAssembly>
*
* <MfgDate>18 Mar 2009</MfgDate>
*
* <FirmwareLoader>SBE 37 FirmwareLoader V 1.0</FirmwareLoader>
*
* <InternalSensors>
*
* <Sensor id='Temperature'>
*
* <type>temperature-1</type>
*
* <SerialNumber>03706896</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Conductivity'>
*
* <type>conductivity-1</type>
*
* <SerialNumber>03706896</SerialNumber>
*
* </Sensor>
*
* </InternalSensors>
*
* </HardwareData>
* <StatusData DeviceType='SBE37SM-RS232' SerialNumber='03706896'>
*
* <DateTime>2023-06-21T20:54:19</DateTime>
*
* <EventSummary numEvents='2'/>
*
* <Power>
*
* <vMain> 6.98</vMain>
*
* <vLith> 3.14</vLith>
*
* </Power>
*
* <MemorySummary>
*
* <Bytes>4807730</Bytes>
*
* <Samples>480773</Samples>
*
* <SamplesFree>358087</SamplesFree>
*
* <SampleLength>10</SampleLength>
*
* </MemorySummary>
*
* <AutonomousSampling>no, stop command</AutonomousSampling>
*
* </StatusData>
* <ConfigurationData DeviceType='SBE37SM-RS232' SerialNumber='03706896'>
*
* <PressureInstalled>no</PressureInstalled>
*
* <ReferencePressure>4.000000e+01</ReferencePressure>
*
* <PumpInstalled>no</PumpInstalled>
*
* <SampleDataFormat>converted engineering</SampleDataFormat>
*
* <OutputSalinity>yes</OutputSalinity>
*
* <OutputSV>no</OutputSV>
*
* <TxRealTime>no</TxRealTime>
*
* <SampleInterval>60</SampleInterval>
*
* <SyncMode>no</SyncMode>
*
* </ConfigurationData>
* <CalibrationCoefficients DeviceType='SBE37SM-RS232' SerialNumber='03706896'>
*
* <Calibration format='TEMP1' id='Temperature'>
*
* <SerialNum>03706896</SerialNum>
*
* <CalDate>24-Nov-21</CalDate>
*
* <A0>6.567388e-05</A0>
*
* <A1>2.670875e-04</A1>
*
* <A2>-1.883997e-06</A2>
*
* <A3>1.378615e-07</A3>
*
* </Calibration>
*
* <Calibration format='WBCOND0' id='Conductivity'>
*
* <SerialNum>03706896</SerialNum>
*
* <CalDate>24-Nov-21</CalDate>
*
* <G>-1.004139e+00</G>
*
* <H>1.542972e-01</H>
*
* <I>-1.626669e-04</I>
*
* <J>3.604198e-05</J>
*
* <PCOR>-9.570000e-08</PCOR>
*
* <TCOR>3.250000e-06</TCOR>
*
* <WBOTC>4.897022e-07</WBOTC>
*
* </Calibration>
*
* </CalibrationCoefficients>
* <EventCounters DeviceType='SBE37SM-RS232' SerialNumber='03706896'>
*
* <EventSummary numEvents='2'/>
*
* <Event type='PON reset' count='1'/>
*
* <Event type='alarm long' count='1'/>
*
* </EventCounters></InstrumentState>
* <UserHeaderInsert>
* <![CDATA[
** WHOTS18 WHOTS18
** 55m 40m
* ]]>
* </UserHeaderInsert>
# nquan = 5
# nvalues = 480773
# units = specified
# name 0 = cond0S/m: Conductivity [S/m]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = prM: Pressure [db]
# name 3 = timeJV2: Time, Instrument [julian days]
# name 4 = flag: 0.000e+00
# span 0 = -0.000035, 5.612707
# span 1 = 0.2936, 31.9805
# span 2 = 40.000, 40.000
# span 3 = 204.000000, 537.869444
# span 4 = 0.0000e+00, 0.0000e+00
# interval = seconds: 60
# start_time = Jul 23 2022 00:00:00 [Instrument's time stamp, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="2" >
# <sensor Channel="1" >
# <!-- Count, Temperature -->
# <TemperatureSensor SensorID="58" >
# <SerialNumber>6896</SerialNumber>
# <CalibrationDate>24-Nov-21</CalibrationDate>
# <A0>6.56738800e-005</A0>
# <A1>2.67087500e-004</A1>
# <A2>-1.88399700e-006</A2>
# <A3>1.37861500e-007</A3>
# <Slope>1.00000000</Slope>
# <Offset>0.0000</Offset>
# </TemperatureSensor>
# </sensor>
# <sensor Channel="2" >
# <!-- Frequency 0, Conductivity -->
# <ConductivitySensor SensorID="3" >
# <SerialNumber>6896</SerialNumber>
# <CalibrationDate>24-Nov-21</CalibrationDate>
# <UseG_J>1</UseG_J>
# <!-- Cell const and series R are applicable only for wide range sensors. -->
# <SeriesR>0.0000</SeriesR>
# <CellConst>2000.0000</CellConst>
# <ConductivityType>1</ConductivityType>
# <Coefficients equation="0" >
# <A>0.00000000e+000</A>
# <B>0.00000000e+000</B>
# <C>0.00000000e+000</C>
# <D>0.00000000e+000</D>
# <M>0.0</M>
# <CPcor>-9.57000000e-008</CPcor>
# </Coefficients>
# <Coefficients equation="1" >
# <G>-1.00413900e+000</G>
# <H>1.54297200e-001</H>
# <I>-1.62666900e-004</I>
# <J>3.60419800e-005</J>
# <CPcor>-9.57000000e-008</CPcor>
# <CTcor>3.2500e-006</CTcor>
# <!-- WBOTC not applicable unless ConductivityType = 1. -->
# <WBOTC>4.89702200e-007</WBOTC>
# </Coefficients>
# <Slope>1.00000000</Slope>
# <Offset>0.00000</Offset>
# </ConductivitySensor>
# </sensor>
# </Sensors>
# datcnv_date = Jun 22 2023 14:28:11, 7.26.7.129 [datcnv_vars = 4]
# datcnv_in = C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_40m_6896_data.hex C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_40m_6896_data.xmlcon
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 6887
* Sea-Bird SBE37SM-RS232 Data File:
* FileName = D:\WHOTS-18_mcat_recovery\w18_45m_6887_data.hex
* Software version SeatermV2 2.8.0.119
* Temperature SN = 6887
* Conductivity SN = 6887
* System UpLoad Time = Jun 21 2023 21:05:25
* sample interval = 75 seconds
* <ApplicationData>
* <Seaterm232>
* <SoftwareVersion>2.8.0.119</SoftwareVersion>
* <BuildDate>07-Nov-2018</BuildDate>
* </Seaterm232>
* </ApplicationData>
* <InstrumentState>
* <HardwareData DeviceType='SBE37SM-RS232' SerialNumber='03706887'>
*
* <Manufacturer>Sea-Bird Electronics, Inc.</Manufacturer>
*
* <FirmwareVersion>3.1</FirmwareVersion>
*
* <FirmwareDate>Jan 20 2012 17:33:01</FirmwareDate>
*
* <PCBAssembly>41647</PCBAssembly>
*
* <PCBAssembly>41610B</PCBAssembly>
*
* <PCBAssembly>41611D</PCBAssembly>
*
* <MfgDate>12 Mar 2009</MfgDate>
*
* <FirmwareLoader>SBE 37 FirmwareLoader V 1.0</FirmwareLoader>
*
* <InternalSensors>
*
* <Sensor id='Temperature'>
*
* <type>temperature-1</type>
*
* <SerialNumber>03706887</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Conductivity'>
*
* <type>conductivity-1</type>
*
* <SerialNumber>03706887</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Pressure'>
*
* <type>strain-0</type>
*
* <SerialNumber>2651319</SerialNumber>
*
* </Sensor>
*
* </InternalSensors>
*
* </HardwareData>
* <StatusData DeviceType='SBE37SM-RS232' SerialNumber='03706887'>
*
* <DateTime>2023-06-21T20:35:52</DateTime>
*
* <EventSummary numEvents='1'/>
*
* <Power>
*
* <vMain> 7.03</vMain>
*
* <vLith> 3.21</vLith>
*
* </Power>
*
* <MemorySummary>
*
* <Bytes>5769030</Bytes>
*
* <Samples>384602</Samples>
*
* <SamplesFree>174638</SamplesFree>
*
* <SampleLength>15</SampleLength>
*
* </MemorySummary>
*
* <AutonomousSampling>no, stop command</AutonomousSampling>
*
* </StatusData>
* <ConfigurationData DeviceType='SBE37SM-RS232' SerialNumber='03706887'>
*
* <PressureInstalled>yes</PressureInstalled>
*
* <PumpInstalled>no</PumpInstalled>
*
* <SampleDataFormat>converted engineering</SampleDataFormat>
*
* <OutputSalinity>yes</OutputSalinity>
*
* <OutputSV>no</OutputSV>
*
* <TxRealTime>no</TxRealTime>
*
* <SampleInterval>75</SampleInterval>
*
* <SyncMode>no</SyncMode>
*
* </ConfigurationData>
* <CalibrationCoefficients DeviceType='SBE37SM-RS232' SerialNumber='03706887'>
*
* <Calibration format='TEMP1' id='Temperature'>
*
* <SerialNum>03706887</SerialNum>
*
* <CalDate>19-Nov-21</CalDate>
*
* <A0>7.349799e-05</A0>
*
* <A1>2.755167e-04</A1>
*
* <A2>-2.572488e-06</A2>
*
* <A3>1.557271e-07</A3>
*
* </Calibration>
*
* <Calibration format='WBCOND0' id='Conductivity'>
*
* <SerialNum>03706887</SerialNum>
*
* <CalDate>19-Nov-21</CalDate>
*
* <G>-1.014648e+00</G>
*
* <H>1.501699e-01</H>
*
* <I>-2.489897e-04</I>
*
* <J>4.121820e-05</J>
*
* <PCOR>-9.570000e-08</PCOR>
*
* <TCOR>3.250000e-06</TCOR>
*
* <WBOTC>4.802827e-07</WBOTC>
*
* </Calibration>
*
* <Calibration format='STRAIN0' id='Pressure'>
*
* <SerialNum>2651319</SerialNum>
*
* <CalDate>02-Nov-21</CalDate>
*
* <PA0>-2.039715e-01</PA0>
*
* <PA1>4.893293e-03</PA1>
*
* <PA2>-2.294833e-11</PA2>
*
* <PTCA0>5.248083e+05</PTCA0>
*
* <PTCA1>1.930555e+00</PTCA1>
*
* <PTCA2>-1.506502e-01</PTCA2>
*
* <PTCB0>2.626762e+01</PTCB0>
*
* <PTCB1>1.250000e-04</PTCB1>
*
* <PTCB2>0.000000e+00</PTCB2>
*
* <PTEMPA0>-7.196676e+01</PTEMPA0>
*
* <PTEMPA1>5.039060e-02</PTEMPA1>
*
* <PTEMPA2>-5.759730e-07</PTEMPA2>
*
* <POFFSET>6.000000e-02</POFFSET>
*
* <PRANGE>1.450000e+03</PRANGE>
*
* </Calibration>
*
* </CalibrationCoefficients>
* <EventCounters DeviceType='SBE37SM-RS232' SerialNumber='03706887'>
*
* <EventSummary numEvents='1'/>
*
* <Event type='PON reset' count='1'/>
*
* </EventCounters></InstrumentState>
* <UserHeaderInsert>
* <![CDATA[
** WHOTS-18
** 45m
* ]]>
* </UserHeaderInsert>
# nquan = 5
# nvalues = 384602
# units = specified
# name 0 = cond0S/m: Conductivity [S/m]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = prdM: Pressure, Strain Gauge [db]
# name 3 = timeJV2: Time, Instrument [julian days]
# name 4 = flag: 0.000e+00
# span 0 = -0.000014, 5.609808
# span 1 = 4.0690, 31.9483
# span 2 = -0.331, 48.792
# span 3 = 204.000000, 537.855035
# span 4 = 0.0000e+00, 0.0000e+00
# interval = seconds: 75
# start_time = Jul 23 2022 00:00:00 [Instrument's time stamp, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="3" >
# <sensor Channel="1" >
# <!-- Count, Temperature -->
# <TemperatureSensor SensorID="58" >
# <SerialNumber>6887</SerialNumber>
# <CalibrationDate>19-Nov-21</CalibrationDate>
# <A0>7.34979900e-005</A0>
# <A1>2.75516700e-004</A1>
# <A2>-2.57248800e-006</A2>
# <A3>1.55727100e-007</A3>
# <Slope>1.00000000</Slope>
# <Offset>0.0000</Offset>
# </TemperatureSensor>
# </sensor>
# <sensor Channel="2" >
# <!-- Frequency 0, Conductivity -->
# <ConductivitySensor SensorID="3" >
# <SerialNumber>6887</SerialNumber>
# <CalibrationDate>19-Nov-21</CalibrationDate>
# <UseG_J>1</UseG_J>
# <!-- Cell const and series R are applicable only for wide range sensors. -->
# <SeriesR>0.0000</SeriesR>
# <CellConst>2000.0000</CellConst>
# <ConductivityType>1</ConductivityType>
# <Coefficients equation="0" >
# <A>0.00000000e+000</A>
# <B>0.00000000e+000</B>
# <C>0.00000000e+000</C>
# <D>0.00000000e+000</D>
# <M>0.0</M>
# <CPcor>-9.57000000e-008</CPcor>
# </Coefficients>
# <Coefficients equation="1" >
# <G>-1.01464800e+000</G>
# <H>1.50169900e-001</H>
# <I>-2.48989700e-004</I>
# <J>4.12182000e-005</J>
# <CPcor>-9.57000000e-008</CPcor>
# <CTcor>3.2500e-006</CTcor>
# <!-- WBOTC not applicable unless ConductivityType = 1. -->
# <WBOTC>4.80282700e-007</WBOTC>
# </Coefficients>
# <Slope>1.00000000</Slope>
# <Offset>0.00000</Offset>
# </ConductivitySensor>
# </sensor>
# <sensor Channel="3" >
# <!-- Count, Pressure, Strain Gauge -->
# <PressureSensor SensorID="46" >
# <SerialNumber>2651319</SerialNumber>
# <CalibrationDate>02-Nov-21</CalibrationDate>
# <PA0>-2.03971500e-001</PA0>
# <PA1>4.89329300e-003</PA1>
# <PA2>-2.29483300e-011</PA2>
# <PTEMPA0>-7.19667600e+001</PTEMPA0>
# <PTEMPA1>5.03906000e-002</PTEMPA1>
# <PTEMPA2>-5.75973000e-007</PTEMPA2>
# <PTCA0>5.24808300e+005</PTCA0>
# <PTCA1>1.93055500e+000</PTCA1>
# <PTCA2>-1.50650200e-001</PTCA2>
# <PTCB0>2.62676200e+001</PTCB0>
# <PTCB1>1.25000000e-004</PTCB1>
# <PTCB2>0.00000000e+000</PTCB2>
# <Offset>0.000000</Offset>
# </PressureSensor>
# </sensor>
# </Sensors>
# datcnv_date = Jun 22 2023 14:29:28, 7.26.7.129 [datcnv_vars = 4]
# datcnv_in = C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_45m_6887_data.hex C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_45m_6887_data.xmlcon
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 6897
* Sea-Bird SBE37SM-RS232 Data File:
* FileName = C:\Users\Jefrey\Documents\WHOTS-18_mcat_recovery\w18_50m_6897_data.hex
* Software version SeatermV2 2.8.0.119
* Temperature SN = 6897
* Conductivity SN = 6897
* System UpLoad Time = Jun 21 2023 18:42:43
* sample interval = 60 seconds
* <ApplicationData>
* <Seaterm232>
* <SoftwareVersion>2.8.0.119</SoftwareVersion>
* <BuildDate>07-Nov-2018</BuildDate>
* </Seaterm232>
* </ApplicationData>
* <InstrumentState>
* <HardwareData DeviceType='SBE37SM-RS232' SerialNumber='03706897'>
*
* <Manufacturer>Sea-Bird Electronics, Inc.</Manufacturer>
*
* <FirmwareVersion>3.1</FirmwareVersion>
*
* <FirmwareDate>Jan 20 2012 17:33:01</FirmwareDate>
*
* <PCBAssembly>41647</PCBAssembly>
*
* <PCBAssembly>41624A</PCBAssembly>
*
* <PCBAssembly>41611D</PCBAssembly>
*
* <MfgDate>18 Mar 2009</MfgDate>
*
* <FirmwareLoader>SBE 37 FirmwareLoader V 1.0</FirmwareLoader>
*
* <InternalSensors>
*
* <Sensor id='Temperature'>
*
* <type>temperature-1</type>
*
* <SerialNumber>03706897</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Conductivity'>
*
* <type>conductivity-1</type>
*
* <SerialNumber>03706897</SerialNumber>
*
* </Sensor>
*
* </InternalSensors>
*
* </HardwareData>
* <StatusData DeviceType='SBE37SM-RS232' SerialNumber='03706897'>
*
* <DateTime>2023-06-21T16:35:45</DateTime>
*
* <EventSummary numEvents='1'/>
*
* <Power>
*
* <vMain> 6.99</vMain>
*
* <vLith> 3.12</vLith>
*
* </Power>
*
* <MemorySummary>
*
* <Bytes>4805140</Bytes>
*
* <Samples>480514</Samples>
*
* <SamplesFree>358346</SamplesFree>
*
* <SampleLength>10</SampleLength>
*
* </MemorySummary>
*
* <AutonomousSampling>no, stop command</AutonomousSampling>
*
* </StatusData>
* <ConfigurationData DeviceType='SBE37SM-RS232' SerialNumber='03706897'>
*
* <PressureInstalled>no</PressureInstalled>
*
* <ReferencePressure>5.000000e+01</ReferencePressure>
*
* <PumpInstalled>no</PumpInstalled>
*
* <SampleDataFormat>converted engineering</SampleDataFormat>
*
* <OutputSalinity>yes</OutputSalinity>
*
* <OutputSV>no</OutputSV>
*
* <TxRealTime>no</TxRealTime>
*
* <SampleInterval>60</SampleInterval>
*
* <SyncMode>no</SyncMode>
*
* </ConfigurationData>
* <CalibrationCoefficients DeviceType='SBE37SM-RS232' SerialNumber='03706897'>
*
* <Calibration format='TEMP1' id='Temperature'>
*
* <SerialNum>03706897</SerialNum>
*
* <CalDate>04-Nov-21</CalDate>
*
* <A0>3.893372e-05</A0>
*
* <A1>2.741949e-04</A1>
*
* <A2>-2.497047e-06</A2>
*
* <A3>1.508359e-07</A3>
*
* </Calibration>
*
* <Calibration format='WBCOND0' id='Conductivity'>
*
* <SerialNum>03706897</SerialNum>
*
* <CalDate>04-Nov-21</CalDate>
*
* <G>-1.005567e+00</G>
*
* <H>1.526919e-01</H>
*
* <I>-3.267329e-04</I>
*
* <J>4.847325e-05</J>
*
* <PCOR>-9.570000e-08</PCOR>
*
* <TCOR>3.250000e-06</TCOR>
*
* <WBOTC>1.296675e-07</WBOTC>
*
* </Calibration>
*
* </CalibrationCoefficients>
* <EventCounters DeviceType='SBE37SM-RS232' SerialNumber='03706897'>
*
* <EventSummary numEvents='1'/>
*
* <Event type='PON reset' count='1'/>
*
* </EventCounters></InstrumentState>
* <UserHeaderInsert>
* <![CDATA[
** WHOTS18 WHOTS18
** 55m 50m
* ]]>
* </UserHeaderInsert>
# nquan = 5
# nvalues = 480514
# units = specified
# name 0 = cond0S/m: Conductivity [S/m]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = prM: Pressure [db]
# name 3 = timeJV2: Time, Instrument [julian days]
# name 4 = flag: 0.000e+00
# span 0 = 0.000023, 5.618516
# span 1 = 0.2104, 27.4332
# span 2 = 50.000, 50.000
# span 3 = 204.000000, 537.689583
# span 4 = 0.0000e+00, 0.0000e+00
# interval = seconds: 60
# start_time = Jul 23 2022 00:00:00 [Instrument's time stamp, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="2" >
# <sensor Channel="1" >
# <!-- Count, Temperature -->
# <TemperatureSensor SensorID="58" >
# <SerialNumber>6897</SerialNumber>
# <CalibrationDate>04-Nov-21</CalibrationDate>
# <A0>3.89337200e-005</A0>
# <A1>2.74194900e-004</A1>
# <A2>-2.49704700e-006</A2>
# <A3>1.50835900e-007</A3>
# <Slope>1.00000000</Slope>
# <Offset>0.0000</Offset>
# </TemperatureSensor>
# </sensor>
# <sensor Channel="2" >
# <!-- Frequency 0, Conductivity -->
# <ConductivitySensor SensorID="3" >
# <SerialNumber>6897</SerialNumber>
# <CalibrationDate>04-Nov-21</CalibrationDate>
# <UseG_J>1</UseG_J>
# <!-- Cell const and series R are applicable only for wide range sensors. -->
# <SeriesR>0.0000</SeriesR>
# <CellConst>2000.0000</CellConst>
# <ConductivityType>1</ConductivityType>
# <Coefficients equation="0" >
# <A>0.00000000e+000</A>
# <B>0.00000000e+000</B>
# <C>0.00000000e+000</C>
# <D>0.00000000e+000</D>
# <M>0.0</M>
# <CPcor>-9.57000000e-008</CPcor>
# </Coefficients>
# <Coefficients equation="1" >
# <G>-1.00556700e+000</G>
# <H>1.52691900e-001</H>
# <I>-3.26732900e-004</I>
# <J>4.84732500e-005</J>
# <CPcor>-9.57000000e-008</CPcor>
# <CTcor>3.2500e-006</CTcor>
# <!-- WBOTC not applicable unless ConductivityType = 1. -->
# <WBOTC>1.29667500e-007</WBOTC>
# </Coefficients>
# <Slope>1.00000000</Slope>
# <Offset>0.00000</Offset>
# </ConductivitySensor>
# </sensor>
# </Sensors>
# datcnv_date = Jun 22 2023 14:33:23, 7.26.7.129 [datcnv_vars = 4]
# datcnv_in = C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_50m_6897_data.hex C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_50m_6897_data.xmlcon
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 6898
* Sea-Bird SBE37SM-RS232 Data File:
* FileName = C:\Users\Jefrey\Documents\WHOTS-18_mcat_recovery\w18_55m_6898_data.hex
* Software version SeatermV2 2.8.0.119
* Temperature SN = 6898
* Conductivity SN = 6898
* System UpLoad Time = Jun 20 2023 22:42:39
* sample interval = 60 seconds
* <ApplicationData>
* <Seaterm232>
* <SoftwareVersion>2.8.0.119</SoftwareVersion>
* <BuildDate>07-Nov-2018</BuildDate>
* </Seaterm232>
* </ApplicationData>
* <InstrumentState>
* <HardwareData DeviceType='SBE37SM-RS232' SerialNumber='03706898'>
*
* <Manufacturer>Sea-Bird Electronics, Inc.</Manufacturer>
*
* <FirmwareVersion>3.1</FirmwareVersion>
*
* <FirmwareDate>Jan 20 2012 17:33:01</FirmwareDate>
*
* <PCBAssembly>41647</PCBAssembly>
*
* <PCBAssembly>41624A</PCBAssembly>
*
* <PCBAssembly>41611D</PCBAssembly>
*
* <MfgDate>18 Mar 2009</MfgDate>
*
* <FirmwareLoader>SBE 37 FirmwareLoader V 1.0</FirmwareLoader>
*
* <InternalSensors>
*
* <Sensor id='Temperature'>
*
* <type>temperature-1</type>
*
* <SerialNumber>03706898</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Conductivity'>
*
* <type>conductivity-1</type>
*
* <SerialNumber>03706898</SerialNumber>
*
* </Sensor>
*
* </InternalSensors>
*
* </HardwareData>
* <StatusData DeviceType='SBE37SM-RS232' SerialNumber='03706898'>
*
* <DateTime>2023-06-20T18:58:00</DateTime>
*
* <EventSummary numEvents='13'/>
*
* <Power>
*
* <vMain> 7.11</vMain>
*
* <vLith> 3.10</vLith>
*
* </Power>
*
* <MemorySummary>
*
* <Bytes>4792080</Bytes>
*
* <Samples>479208</Samples>
*
* <SamplesFree>359652</SamplesFree>
*
* <SampleLength>10</SampleLength>
*
* </MemorySummary>
*
* <AutonomousSampling>no, stop command</AutonomousSampling>
*
* </StatusData>
* <ConfigurationData DeviceType='SBE37SM-RS232' SerialNumber='03706898'>
*
* <PressureInstalled>no</PressureInstalled>
*
* <ReferencePressure>5.500000e+01</ReferencePressure>
*
* <PumpInstalled>no</PumpInstalled>
*
* <SampleDataFormat>converted engineering</SampleDataFormat>
*
* <OutputSalinity>yes</OutputSalinity>
*
* <OutputSV>no</OutputSV>
*
* <TxRealTime>yes</TxRealTime>
*
* <SampleInterval>60</SampleInterval>
*
* <SyncMode>no</SyncMode>
*
* </ConfigurationData>
* <CalibrationCoefficients DeviceType='SBE37SM-RS232' SerialNumber='03706898'>
*
* <Calibration format='TEMP1' id='Temperature'>
*
* <SerialNum>03706898</SerialNum>
*
* <CalDate>02-Dec-21</CalDate>
*
* <A0>9.450561e-05</A0>
*
* <A1>2.642366e-04</A1>
*
* <A2>-1.702430e-06</A2>
*
* <A3>1.318726e-07</A3>
*
* </Calibration>
*
* <Calibration format='WBCOND0' id='Conductivity'>
*
* <SerialNum>03706898</SerialNum>
*
* <CalDate>02-Dec-21</CalDate>
*
* <G>-1.019711e+00</G>
*
* <H>1.534926e-01</H>
*
* <I>-1.896768e-04</I>
*
* <J>3.825842e-05</J>
*
* <PCOR>-9.570000e-08</PCOR>
*
* <TCOR>3.250000e-06</TCOR>
*
* <WBOTC>2.261411e-07</WBOTC>
*
* </Calibration>
*
* </CalibrationCoefficients>
* <EventCounters DeviceType='SBE37SM-RS232' SerialNumber='03706898'>
*
* <EventSummary numEvents='13'/>
*
* <Event type='PON reset' count='13'/>
*
* </EventCounters></InstrumentState>
* <UserHeaderInsert>
* <![CDATA[
** WHOTS18
** 55m
* ]]>
* </UserHeaderInsert>
# nquan = 5
# nvalues = 479208
# units = specified
# name 0 = cond0S/m: Conductivity [S/m]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = prM: Pressure [db]
# name 3 = timeJV2: Time, Instrument [julian days]
# name 4 = flag: 0.000e+00
# span 0 = 5.9090e-07, 5.608256
# span 1 = 0.2780, 27.4126
# span 2 = 55.000, 55.000
# span 3 = 204.000000, 536.782639
# span 4 = 0.0000e+00, 0.0000e+00
# interval = seconds: 60
# start_time = Jul 23 2022 00:00:00 [Instrument's time stamp, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="2" >
# <sensor Channel="1" >
# <!-- Count, Temperature -->
# <TemperatureSensor SensorID="58" >
# <SerialNumber>6898</SerialNumber>
# <CalibrationDate>02-Dec-21</CalibrationDate>
# <A0>9.45056100e-005</A0>
# <A1>2.64236600e-004</A1>
# <A2>-1.70243000e-006</A2>
# <A3>1.31872600e-007</A3>
# <Slope>1.00000000</Slope>
# <Offset>0.0000</Offset>
# </TemperatureSensor>
# </sensor>
# <sensor Channel="2" >
# <!-- Frequency 0, Conductivity -->
# <ConductivitySensor SensorID="3" >
# <SerialNumber>6898</SerialNumber>
# <CalibrationDate>02-Dec-21</CalibrationDate>
# <UseG_J>1</UseG_J>
# <!-- Cell const and series R are applicable only for wide range sensors. -->
# <SeriesR>0.0000</SeriesR>
# <CellConst>2000.0000</CellConst>
# <ConductivityType>1</ConductivityType>
# <Coefficients equation="0" >
# <A>0.00000000e+000</A>
# <B>0.00000000e+000</B>
# <C>0.00000000e+000</C>
# <D>0.00000000e+000</D>
# <M>0.0</M>
# <CPcor>-9.57000000e-008</CPcor>
# </Coefficients>
# <Coefficients equation="1" >
# <G>-1.01971100e+000</G>
# <H>1.53492600e-001</H>
# <I>-1.89676800e-004</I>
# <J>3.82584200e-005</J>
# <CPcor>-9.57000000e-008</CPcor>
# <CTcor>3.2500e-006</CTcor>
# <!-- WBOTC not applicable unless ConductivityType = 1. -->
# <WBOTC>2.26141100e-007</WBOTC>
# </Coefficients>
# <Slope>1.00000000</Slope>
# <Offset>0.00000</Offset>
# </ConductivitySensor>
# </sensor>
# </Sensors>
# datcnv_date = Jun 22 2023 14:37:38, 7.26.7.129 [datcnv_vars = 4]
# datcnv_in = C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_55m_6898_data.hex C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_55m_6898_data.xmlcon
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 6899
* Sea-Bird SBE37SM-RS232 Data File:
* FileName = C:\Users\Jefrey\Documents\WHOTS-18_mcat_recovery\w18_65m_6899_data.hex
* Software version SeatermV2 2.8.0.119
* Temperature SN = 6899
* Conductivity SN = 6899
* System UpLoad Time = Jun 21 2023 16:23:52
* sample interval = 60 seconds
* <ApplicationData>
* <Seaterm232>
* <SoftwareVersion>2.8.0.119</SoftwareVersion>
* <BuildDate>07-Nov-2018</BuildDate>
* </Seaterm232>
* </ApplicationData>
* <InstrumentState>
* <HardwareData DeviceType='SBE37SM-RS232' SerialNumber='03706899'>
*
* <Manufacturer>Sea-Bird Electronics, Inc.</Manufacturer>
*
* <FirmwareVersion>3.1</FirmwareVersion>
*
* <FirmwareDate>Jan 20 2012 17:33:01</FirmwareDate>
*
* <PCBAssembly>41647</PCBAssembly>
*
* <PCBAssembly>41624A</PCBAssembly>
*
* <PCBAssembly>41611D</PCBAssembly>
*
* <MfgDate>18 Mar 2009</MfgDate>
*
* <FirmwareLoader>SBE 37 FirmwareLoader V 1.0</FirmwareLoader>
*
* <InternalSensors>
*
* <Sensor id='Temperature'>
*
* <type>temperature-1</type>
*
* <SerialNumber>03706899</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Conductivity'>
*
* <type>conductivity-1</type>
*
* <SerialNumber>03706899</SerialNumber>
*
* </Sensor>
*
* </InternalSensors>
*
* </HardwareData>
* <StatusData DeviceType='SBE37SM-RS232' SerialNumber='03706899'>
*
* <DateTime>2023-06-21T15:04:33</DateTime>
*
* <EventSummary numEvents='1'/>
*
* <Power>
*
* <vMain> 6.92</vMain>
*
* <vLith> 3.08</vLith>
*
* </Power>
*
* <MemorySummary>
*
* <Bytes>4804240</Bytes>
*
* <Samples>480424</Samples>
*
* <SamplesFree>358436</SamplesFree>
*
* <SampleLength>10</SampleLength>
*
* </MemorySummary>
*
* <AutonomousSampling>no, stop command</AutonomousSampling>
*
* </StatusData>
* <ConfigurationData DeviceType='SBE37SM-RS232' SerialNumber='03706899'>
*
* <PressureInstalled>no</PressureInstalled>
*
* <ReferencePressure>6.500000e+01</ReferencePressure>
*
* <PumpInstalled>no</PumpInstalled>
*
* <SampleDataFormat>converted engineering</SampleDataFormat>
*
* <OutputSalinity>no</OutputSalinity>
*
* <OutputSV>no</OutputSV>
*
* <TxRealTime>no</TxRealTime>
*
* <SampleInterval>60</SampleInterval>
*
* <SyncMode>no</SyncMode>
*
* </ConfigurationData>
* <CalibrationCoefficients DeviceType='SBE37SM-RS232' SerialNumber='03706899'>
*
* <Calibration format='TEMP1' id='Temperature'>
*
* <SerialNum>03706899</SerialNum>
*
* <CalDate>13-Nov-21</CalDate>
*
* <A0>5.929491e-05</A0>
*
* <A1>2.752034e-04</A1>
*
* <A2>-2.505302e-06</A2>
*
* <A3>1.544594e-07</A3>
*
* </Calibration>
*
* <Calibration format='WBCOND0' id='Conductivity'>
*
* <SerialNum>03706899</SerialNum>
*
* <CalDate>13-Nov-21</CalDate>
*
* <G>-1.021210e+00</G>
*
* <H>1.508593e-01</H>
*
* <I>-2.971312e-04</I>
*
* <J>4.524669e-05</J>
*
* <PCOR>-9.570000e-08</PCOR>
*
* <TCOR>3.250000e-06</TCOR>
*
* <WBOTC>3.837484e-07</WBOTC>
*
* </Calibration>
*
* </CalibrationCoefficients>
* <EventCounters DeviceType='SBE37SM-RS232' SerialNumber='03706899'>
*
* <EventSummary numEvents='1'/>
*
* <Event type='PON reset' count='1'/>
*
* </EventCounters></InstrumentState>
* <UserHeaderInsert>
* <![CDATA[
** WHOTS18 WHOTS18
** 55m 65m
* ]]>
* </UserHeaderInsert>
# nquan = 5
# nvalues = 480424
# units = specified
# name 0 = cond0S/m: Conductivity [S/m]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = prM: Pressure [db]
# name 3 = timeJV2: Time, Instrument [julian days]
# name 4 = flag: 0.000e+00
# span 0 = -0.000019, 5.593476
# span 1 = 0.1927, 27.3415
# span 2 = 65.000, 65.000
# span 3 = 204.000000, 537.627083
# span 4 = 0.0000e+00, 0.0000e+00
# interval = seconds: 60
# start_time = Jul 23 2022 00:00:00 [Instrument's time stamp, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="2" >
# <sensor Channel="1" >
# <!-- Count, Temperature -->
# <TemperatureSensor SensorID="58" >
# <SerialNumber>6899</SerialNumber>
# <CalibrationDate>13-Nov-21</CalibrationDate>
# <A0>5.92949100e-005</A0>
# <A1>2.75203400e-004</A1>
# <A2>-2.50530200e-006</A2>
# <A3>1.54459400e-007</A3>
# <Slope>1.00000000</Slope>
# <Offset>0.0000</Offset>
# </TemperatureSensor>
# </sensor>
# <sensor Channel="2" >
# <!-- Frequency 0, Conductivity -->
# <ConductivitySensor SensorID="3" >
# <SerialNumber>6899</SerialNumber>
# <CalibrationDate>13-Nov-21</CalibrationDate>
# <UseG_J>1</UseG_J>
# <!-- Cell const and series R are applicable only for wide range sensors. -->
# <SeriesR>0.0000</SeriesR>
# <CellConst>2000.0000</CellConst>
# <ConductivityType>1</ConductivityType>
# <Coefficients equation="0" >
# <A>0.00000000e+000</A>
# <B>0.00000000e+000</B>
# <C>0.00000000e+000</C>
# <D>0.00000000e+000</D>
# <M>0.0</M>
# <CPcor>-9.57000000e-008</CPcor>
# </Coefficients>
# <Coefficients equation="1" >
# <G>-1.02121000e+000</G>
# <H>1.50859300e-001</H>
# <I>-2.97131200e-004</I>
# <J>4.52466900e-005</J>
# <CPcor>-9.57000000e-008</CPcor>
# <CTcor>3.2500e-006</CTcor>
# <!-- WBOTC not applicable unless ConductivityType = 1. -->
# <WBOTC>3.83748400e-007</WBOTC>
# </Coefficients>
# <Slope>1.00000000</Slope>
# <Offset>0.00000</Offset>
# </ConductivitySensor>
# </sensor>
# </Sensors>
# datcnv_date = Jun 22 2023 14:34:00, 7.26.7.129 [datcnv_vars = 4]
# datcnv_in = C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_65m_6899_data.hex C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_65m_6899_data.xmlcon
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 3618
* Sea-Bird SBE37 Data File:
* FileName = D:\WHOTS-18_mcat_recovery\w18_75m_3618_data.asc
* Software Version 1.59
* Temperature SN = 3618
* Conductivity SN = 3618
* System UpLoad Time = Jun 20 2023 22:32:39
** WHOTS-18
** 75m
* ds
* SBE37-SM V 2.6b SERIAL NO. 3618 20 Jun 2023 22:31:26
* not logging: received stop command
* sample interval = 180 seconds
* samplenumber = 159809, free = 73207
* do not transmit real-time data
* output salinity with each sample
* do not output sound velocity with each sample
* store time with each sample
* number of samples to average = 4
* reference pressure = 75.0 db
* serial sync mode disabled
* wait time after serial sync sampling = 30 seconds
* internal pump not installed
* temperature = 19.07 deg C
* S>
* SBE37-SM V 2.6b 3618
* temperature: 04-nov-21
* TA0 = -7.245919e-05
* TA1 = 2.883522e-04
* TA2 = -3.225646e-06
* TA3 = 1.790927e-07
* conductivity: 04-nov-21
* G = -1.007241e+00
* H = 1.387097e-01
* I = 2.797664e-04
* J = 1.572639e-05
* CPCOR = -9.570000e-08
* CTCOR = 3.250000e-06
* WBOTC = -1.110161e-05
* rtc: 04-nov-21
* RTCA0 = 9.999764e-01
* RTCA1 = 1.754173e-06
* RTCA2 = -3.347873e-08
* S>
*END*
# Metadata for Sensor Serial Number: 3634
* Sea-Bird SBE37 Data File:
* FileName = D:\WHOTS-18_mcat_recovery\w18__85m_3634_data.asc
* Software Version 1.59
* Temperature SN = 3634
* Conductivity SN = 3634
* System UpLoad Time = Jun 21 2023 05:37:43
** WHOTS-18
** 85m
* ds
* SBE37-SM V 2.6b SERIAL NO. 3634 06-21-2023 05:36:24
* not logging: received stop command
* sample interval = 180 seconds
* samplenumber = 159951, free = 73065
* do not transmit real-time data
* output salinity with each sample
* do not output sound velocity with each sample
* store time with each sample
* number of samples to average = 4
* reference pressure = 85.0 db
* serial sync mode disabled
* wait time after serial sync sampling = 30 seconds
* internal pump not installed
* temperature = 19.98 deg C
* S>
* SBE37-SM V 2.6b 3634
* temperature: 13-nov-21
* TA0 = -4.900056e-05
* TA1 = 2.811162e-04
* TA2 = -2.863184e-06
* TA3 = 1.640679e-07
* conductivity: 13-nov-21
* G = -1.019645e+00
* H = 1.467542e-01
* I = -1.326342e-04
* J = 3.543132e-05
* CPCOR = -9.570000e-08
* CTCOR = 3.250000e-06
* WBOTC = -1.225817e-05
* rtc: 13-nov-21
* RTCA0 = 9.999831e-01
* RTCA1 = 1.739713e-06
* RTCA2 = -3.278574e-08
* S>
*END*
# Metadata for Sensor Serial Number: 3670
* Sea-Bird SBE37 Data File:
* FileName = D:\WHOTS-18_mcat_recovery\w18_95m_3870_data.asc
* Software Version 1.59
* Temperature SN = 3670
* Conductivity SN = 3670
* System UpLoad Time = Jun 20 2023 19:34:55
** WHOTS-18
** 95m
* ds
* SBE37-SM V 2.6b SERIAL NO. 3670 20 Jun 2023 19:33:36
* not logging: received stop command
* sample interval = 240 seconds
* samplenumber = 119813, free = 70837
* do not transmit real-time data
* do not output salinity with each sample
* do not output sound velocity with each sample
* store time with each sample
* number of samples to average = 4
* serial sync mode disabled
* wait time after serial sync sampling = 30 seconds
* internal pump not installed
* temperature = 18.83 deg C
* S>
* SBE37-SM V 2.6b 3670
* temperature: 19-nov-21
* TA0 = -2.217529e-04
* TA1 = 3.125302e-04
* TA2 = -4.715840e-06
* TA3 = 2.118395e-07
* conductivity: 19-nov-21
* G = -1.012115e+00
* H = 1.231429e-01
* I = -9.476538e-05
* J = 2.603631e-05
* CPCOR = -9.570000e-08
* CTCOR = 3.250000e-06
* WBOTC = -8.688073e-06
* pressure S/N 5701, range = 1450 psia: 03-nov-21
* PA0 = -5.344184e-02
* PA1 = 6.860336e-02
* PA2 = -4.245815e-09
* PTCA0 = -2.001202e+02
* PTCA1 = -6.639637e-02
* PTCA2 = 1.408200e-03
* PTCSB0 = 2.491775e+01
* PTCSB1 = -6.500000e-04
* PTCSB2 = 0.000000e+00
* POFFSET = -1.230000e+00
* rtc: 19-nov-21
* RTCA0 = 9.999888e-01
* RTCA1 = 1.835673e-06
* RTCA2 = -3.505132e-08
* S>
*END*
# Metadata for Sensor Serial Number: 6889
* Sea-Bird SBE37SM-RS232 Data File:
* FileName = C:\Users\Jefrey\Documents\WHOTS-18_mcat_recovery\w18_105m_6889_data.hex
* Software version SeatermV2 2.8.0.119
* Temperature SN = 6889
* Conductivity SN = 6889
* System UpLoad Time = Jun 21 2023 06:28:47
* sample interval = 75 seconds
* <ApplicationData>
* <Seaterm232>
* <SoftwareVersion>2.8.0.119</SoftwareVersion>
* <BuildDate>07-Nov-2018</BuildDate>
* </Seaterm232>
* </ApplicationData>
* <InstrumentState>
* <HardwareData DeviceType='SBE37SM-RS232' SerialNumber='03706889'>
*
* <Manufacturer>Sea-Bird Electronics, Inc.</Manufacturer>
*
* <FirmwareVersion>3.1</FirmwareVersion>
*
* <FirmwareDate>Jan 20 2012 17:33:01</FirmwareDate>
*
* <PCBAssembly>41647</PCBAssembly>
*
* <PCBAssembly>41610B</PCBAssembly>
*
* <PCBAssembly>41611D</PCBAssembly>
*
* <MfgDate>13 Mar 2009</MfgDate>
*
* <FirmwareLoader>SBE 37 FirmwareLoader V 1.0</FirmwareLoader>
*
* <InternalSensors>
*
* <Sensor id='Temperature'>
*
* <type>temperature-1</type>
*
* <SerialNumber>03706889</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Conductivity'>
*
* <type>conductivity-1</type>
*
* <SerialNumber>03706889</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Pressure'>
*
* <type>strain-0</type>
*
* <SerialNumber>2651321</SerialNumber>
*
* </Sensor>
*
* </InternalSensors>
*
* </HardwareData>
* <StatusData DeviceType='SBE37SM-RS232' SerialNumber='03706889'>
*
* <DateTime>2023-06-21T03:56:07</DateTime>
*
* <EventSummary numEvents='1'/>
*
* <Power>
*
* <vMain> 6.85</vMain>
*
* <vLith> 3.14</vLith>
*
* </Power>
*
* <MemorySummary>
*
* <Bytes>5756400</Bytes>
*
* <Samples>383760</Samples>
*
* <SamplesFree>175480</SamplesFree>
*
* <SampleLength>15</SampleLength>
*
* </MemorySummary>
*
* <AutonomousSampling>no, stop command</AutonomousSampling>
*
* </StatusData>
* <ConfigurationData DeviceType='SBE37SM-RS232' SerialNumber='03706889'>
*
* <PressureInstalled>yes</PressureInstalled>
*
* <PumpInstalled>no</PumpInstalled>
*
* <SampleDataFormat>converted engineering</SampleDataFormat>
*
* <OutputSalinity>yes</OutputSalinity>
*
* <OutputSV>no</OutputSV>
*
* <TxRealTime>no</TxRealTime>
*
* <SampleInterval>75</SampleInterval>
*
* <SyncMode>no</SyncMode>
*
* </ConfigurationData>
* <CalibrationCoefficients DeviceType='SBE37SM-RS232' SerialNumber='03706889'>
*
* <Calibration format='TEMP1' id='Temperature'>
*
* <SerialNum>03706889</SerialNum>
*
* <CalDate>10-Nov-21</CalDate>
*
* <A0>1.016718e-04</A0>
*
* <A1>2.610141e-04</A1>
*
* <A2>-1.424935e-06</A2>
*
* <A3>1.246406e-07</A3>
*
* </Calibration>
*
* <Calibration format='WBCOND0' id='Conductivity'>
*
* <SerialNum>03706889</SerialNum>
*
* <CalDate>10-Nov-21</CalDate>
*
* <G>-9.999722e-01</G>
*
* <H>1.501833e-01</H>
*
* <I>-2.695119e-04</I>
*
* <J>4.302018e-05</J>
*
* <PCOR>-9.570000e-08</PCOR>
*
* <TCOR>3.250000e-06</TCOR>
*
* <WBOTC>1.290011e-07</WBOTC>
*
* </Calibration>
*
* <Calibration format='STRAIN0' id='Pressure'>
*
* <SerialNum>2651321</SerialNum>
*
* <CalDate>02-Nov-21</CalDate>
*
* <PA0>3.430363e-01</PA0>
*
* <PA1>5.078449e-03</PA1>
*
* <PA2>-1.305139e-11</PA2>
*
* <PTCA0>5.247892e+05</PTCA0>
*
* <PTCA1>2.344197e+00</PTCA1>
*
* <PTCA2>3.608461e-03</PTCA2>
*
* <PTCB0>2.627775e+01</PTCB0>
*
* <PTCB1>-1.250000e-03</PTCB1>
*
* <PTCB2>0.000000e+00</PTCB2>
*
* <PTEMPA0>-6.960694e+01</PTEMPA0>
*
* <PTEMPA1>5.057417e-02</PTEMPA1>
*
* <PTEMPA2>-4.275673e-07</PTEMPA2>
*
* <POFFSET>7.999999e-02</POFFSET>
*
* <PRANGE>1.450000e+03</PRANGE>
*
* </Calibration>
*
* </CalibrationCoefficients>
* <EventCounters DeviceType='SBE37SM-RS232' SerialNumber='03706889'>
*
* <EventSummary numEvents='1'/>
*
* <Event type='PON reset' count='1'/>
*
* </EventCounters></InstrumentState>
* <UserHeaderInsert>
* <![CDATA[
** WHOTS18 WHOTS18
** 55m 105m
* ]]>
* </UserHeaderInsert>
# nquan = 5
# nvalues = 383760
# units = specified
# name 0 = cond0S/m: Conductivity [S/m]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = prdM: Pressure, Strain Gauge [db]
# name 3 = timeJV2: Time, Instrument [julian days]
# name 4 = flag: 0.000e+00
# span 0 = 0.000014, 5.459091
# span 1 = 0.9936, 26.4614
# span 2 = -0.594, 108.979
# span 3 = 204.000000, 537.124132
# span 4 = 0.0000e+00, 0.0000e+00
# interval = seconds: 75
# start_time = Jul 23 2022 00:00:00 [Instrument's time stamp, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="3" >
# <sensor Channel="1" >
# <!-- Count, Temperature -->
# <TemperatureSensor SensorID="58" >
# <SerialNumber>6889</SerialNumber>
# <CalibrationDate>10-Nov-21</CalibrationDate>
# <A0>1.01671800e-004</A0>
# <A1>2.61014100e-004</A1>
# <A2>-1.42493500e-006</A2>
# <A3>1.24640600e-007</A3>
# <Slope>1.00000000</Slope>
# <Offset>0.0000</Offset>
# </TemperatureSensor>
# </sensor>
# <sensor Channel="2" >
# <!-- Frequency 0, Conductivity -->
# <ConductivitySensor SensorID="3" >
# <SerialNumber>6889</SerialNumber>
# <CalibrationDate>10-Nov-21</CalibrationDate>
# <UseG_J>1</UseG_J>
# <!-- Cell const and series R are applicable only for wide range sensors. -->
# <SeriesR>0.0000</SeriesR>
# <CellConst>2000.0000</CellConst>
# <ConductivityType>1</ConductivityType>
# <Coefficients equation="0" >
# <A>0.00000000e+000</A>
# <B>0.00000000e+000</B>
# <C>0.00000000e+000</C>
# <D>0.00000000e+000</D>
# <M>0.0</M>
# <CPcor>-9.57000000e-008</CPcor>
# </Coefficients>
# <Coefficients equation="1" >
# <G>-9.99972200e-001</G>
# <H>1.50183300e-001</H>
# <I>-2.69511900e-004</I>
# <J>4.30201800e-005</J>
# <CPcor>-9.57000000e-008</CPcor>
# <CTcor>3.2500e-006</CTcor>
# <!-- WBOTC not applicable unless ConductivityType = 1. -->
# <WBOTC>1.29001100e-007</WBOTC>
# </Coefficients>
# <Slope>1.00000000</Slope>
# <Offset>0.00000</Offset>
# </ConductivitySensor>
# </sensor>
# <sensor Channel="3" >
# <!-- Count, Pressure, Strain Gauge -->
# <PressureSensor SensorID="46" >
# <SerialNumber>2651321</SerialNumber>
# <CalibrationDate>02-Nov-21</CalibrationDate>
# <PA0>3.43036300e-001</PA0>
# <PA1>5.07844900e-003</PA1>
# <PA2>-1.30513900e-011</PA2>
# <PTEMPA0>-6.96069400e+001</PTEMPA0>
# <PTEMPA1>5.05741700e-002</PTEMPA1>
# <PTEMPA2>-4.27567300e-007</PTEMPA2>
# <PTCA0>5.24789200e+005</PTCA0>
# <PTCA1>2.34419700e+000</PTCA1>
# <PTCA2>3.60846100e-003</PTCA2>
# <PTCB0>2.62777500e+001</PTCB0>
# <PTCB1>-1.25000000e-003</PTCB1>
# <PTCB2>0.00000000e+000</PTCB2>
# <Offset>0.000000</Offset>
# </PressureSensor>
# </sensor>
# </Sensors>
# datcnv_date = Jun 22 2023 14:36:18, 7.26.7.129 [datcnv_vars = 4]
# datcnv_in = C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_105m_6889_data.hex C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_105m_6889_data.xmlcon
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 6890
* Sea-Bird SBE37SM-RS232 Data File:
* FileName = C:\Users\Jefrey\Documents\WHOTS-18_mcat_recovery\w18_120m_6890_data.hex
* Software version SeatermV2 2.8.0.119
* Temperature SN = 6890
* Conductivity SN = 6890
* System UpLoad Time = Jun 21 2023 01:35:59
* sample interval = 75 seconds
* <ApplicationData>
* <Seaterm232>
* <SoftwareVersion>2.8.0.119</SoftwareVersion>
* <BuildDate>07-Nov-2018</BuildDate>
* </Seaterm232>
* </ApplicationData>
* <InstrumentState>
* <HardwareData DeviceType='SBE37SM-RS232' SerialNumber='03706890'>
*
* <Manufacturer>Sea-Bird Electronics, Inc.</Manufacturer>
*
* <FirmwareVersion>3.1</FirmwareVersion>
*
* <FirmwareDate>Jan 20 2012 17:33:01</FirmwareDate>
*
* <PCBAssembly>41647</PCBAssembly>
*
* <PCBAssembly>41610B</PCBAssembly>
*
* <PCBAssembly>41611D</PCBAssembly>
*
* <MfgDate>13 Mar 2009</MfgDate>
*
* <FirmwareLoader>SBE 37 FirmwareLoader V 1.0</FirmwareLoader>
*
* <InternalSensors>
*
* <Sensor id='Temperature'>
*
* <type>temperature-1</type>
*
* <SerialNumber>03706890</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Conductivity'>
*
* <type>conductivity-1</type>
*
* <SerialNumber>03706890</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Pressure'>
*
* <type>strain-0</type>
*
* <SerialNumber>2651322</SerialNumber>
*
* </Sensor>
*
* </InternalSensors>
*
* </HardwareData>
* <StatusData DeviceType='SBE37SM-RS232' SerialNumber='03706890'>
*
* <DateTime>2023-06-20T23:03:29</DateTime>
*
* <EventSummary numEvents='1'/>
*
* <Power>
*
* <vMain> 6.88</vMain>
*
* <vLith> 3.12</vLith>
*
* </Power>
*
* <MemorySummary>
*
* <Bytes>5753505</Bytes>
*
* <Samples>383567</Samples>
*
* <SamplesFree>175673</SamplesFree>
*
* <SampleLength>15</SampleLength>
*
* </MemorySummary>
*
* <AutonomousSampling>no, stop command</AutonomousSampling>
*
* </StatusData>
* <ConfigurationData DeviceType='SBE37SM-RS232' SerialNumber='03706890'>
*
* <PressureInstalled>yes</PressureInstalled>
*
* <PumpInstalled>no</PumpInstalled>
*
* <SampleDataFormat>converted engineering</SampleDataFormat>
*
* <OutputSalinity>yes</OutputSalinity>
*
* <OutputSV>no</OutputSV>
*
* <TxRealTime>no</TxRealTime>
*
* <SampleInterval>75</SampleInterval>
*
* <SyncMode>no</SyncMode>
*
* </ConfigurationData>
* <CalibrationCoefficients DeviceType='SBE37SM-RS232' SerialNumber='03706890'>
*
* <Calibration format='TEMP1' id='Temperature'>
*
* <SerialNum>03706890</SerialNum>
*
* <CalDate>19-Nov-21</CalDate>
*
* <A0>4.151677e-05</A0>
*
* <A1>2.718070e-04</A1>
*
* <A2>-2.312460e-06</A2>
*
* <A3>1.463529e-07</A3>
*
* </Calibration>
*
* <Calibration format='WBCOND0' id='Conductivity'>
*
* <SerialNum>03706890</SerialNum>
*
* <CalDate>19-Nov-21</CalDate>
*
* <G>-1.018172e+00</G>
*
* <H>1.598801e-01</H>
*
* <I>-2.824857e-04</I>
*
* <J>4.703804e-05</J>
*
* <PCOR>-9.570000e-08</PCOR>
*
* <TCOR>3.250000e-06</TCOR>
*
* <WBOTC>1.319142e-07</WBOTC>
*
* </Calibration>
*
* <Calibration format='STRAIN0' id='Pressure'>
*
* <SerialNum>2651322</SerialNum>
*
* <CalDate>03-Nov-21</CalDate>
*
* <PA0>-1.945177e-01</PA0>
*
* <PA1>4.560412e-03</PA1>
*
* <PA2>-1.846598e-11</PA2>
*
* <PTCA0>5.247655e+05</PTCA0>
*
* <PTCA1>1.259274e+00</PTCA1>
*
* <PTCA2>-1.174853e-01</PTCA2>
*
* <PTCB0>2.625275e+01</PTCB0>
*
* <PTCB1>-2.500000e-04</PTCB1>
*
* <PTCB2>0.000000e+00</PTCB2>
*
* <PTEMPA0>-7.286258e+01</PTEMPA0>
*
* <PTEMPA1>5.015612e-02</PTEMPA1>
*
* <PTEMPA2>-4.160485e-07</PTEMPA2>
*
* <POFFSET>4.000000e-02</POFFSET>
*
* <PRANGE>1.450000e+03</PRANGE>
*
* </Calibration>
*
* </CalibrationCoefficients>
* <EventCounters DeviceType='SBE37SM-RS232' SerialNumber='03706890'>
*
* <EventSummary numEvents='1'/>
*
* <Event type='PON reset' count='1'/>
*
* </EventCounters></InstrumentState>
* <UserHeaderInsert>
* <![CDATA[
** WHOTS18 WHOTS-18
** 55m 120m
* ]]>
* </UserHeaderInsert>
# nquan = 5
# nvalues = 383567
# units = specified
# name 0 = cond0S/m: Conductivity [S/m]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = prdM: Pressure, Strain Gauge [db]
# name 3 = timeJV2: Time, Instrument [julian days]
# name 4 = flag: 0.000e+00
# span 0 = 0.000002, 5.415308
# span 1 = 1.0164, 27.9001
# span 2 = -0.259, 123.876
# span 3 = 204.000000, 536.956597
# span 4 = 0.0000e+00, 0.0000e+00
# interval = seconds: 75
# start_time = Jul 23 2022 00:00:00 [Instrument's time stamp, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="3" >
# <sensor Channel="1" >
# <!-- Count, Temperature -->
# <TemperatureSensor SensorID="58" >
# <SerialNumber>6890</SerialNumber>
# <CalibrationDate>19-Nov-21</CalibrationDate>
# <A0>4.15167700e-005</A0>
# <A1>2.71807000e-004</A1>
# <A2>-2.31246000e-006</A2>
# <A3>1.46352900e-007</A3>
# <Slope>1.00000000</Slope>
# <Offset>0.0000</Offset>
# </TemperatureSensor>
# </sensor>
# <sensor Channel="2" >
# <!-- Frequency 0, Conductivity -->
# <ConductivitySensor SensorID="3" >
# <SerialNumber>6890</SerialNumber>
# <CalibrationDate>19-Nov-21</CalibrationDate>
# <UseG_J>1</UseG_J>
# <!-- Cell const and series R are applicable only for wide range sensors. -->
# <SeriesR>0.0000</SeriesR>
# <CellConst>2000.0000</CellConst>
# <ConductivityType>1</ConductivityType>
# <Coefficients equation="0" >
# <A>0.00000000e+000</A>
# <B>0.00000000e+000</B>
# <C>0.00000000e+000</C>
# <D>0.00000000e+000</D>
# <M>0.0</M>
# <CPcor>-9.57000000e-008</CPcor>
# </Coefficients>
# <Coefficients equation="1" >
# <G>-1.01817200e+000</G>
# <H>1.59880100e-001</H>
# <I>-2.82485700e-004</I>
# <J>4.70380400e-005</J>
# <CPcor>-9.57000000e-008</CPcor>
# <CTcor>3.2500e-006</CTcor>
# <!-- WBOTC not applicable unless ConductivityType = 1. -->
# <WBOTC>1.31914200e-007</WBOTC>
# </Coefficients>
# <Slope>1.00000000</Slope>
# <Offset>0.00000</Offset>
# </ConductivitySensor>
# </sensor>
# <sensor Channel="3" >
# <!-- Count, Pressure, Strain Gauge -->
# <PressureSensor SensorID="46" >
# <SerialNumber>2651322</SerialNumber>
# <CalibrationDate>03-Nov-21</CalibrationDate>
# <PA0>-1.94517700e-001</PA0>
# <PA1>4.56041200e-003</PA1>
# <PA2>-1.84659800e-011</PA2>
# <PTEMPA0>-7.28625800e+001</PTEMPA0>
# <PTEMPA1>5.01561200e-002</PTEMPA1>
# <PTEMPA2>-4.16048500e-007</PTEMPA2>
# <PTCA0>5.24765500e+005</PTCA0>
# <PTCA1>1.25927400e+000</PTCA1>
# <PTCA2>-1.17485300e-001</PTCA2>
# <PTCB0>2.62527500e+001</PTCB0>
# <PTCB1>-2.50000000e-004</PTCB1>
# <PTCB2>0.00000000e+000</PTCB2>
# <Offset>0.000000</Offset>
# </PressureSensor>
# </sensor>
# </Sensors>
# datcnv_date = Jun 22 2023 14:36:54, 7.26.7.129 [datcnv_vars = 4]
# datcnv_in = C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_120m_6890_data.hex C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_120m_6890_data.xmlcon
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 6888
* Sea-Bird SBE37SM-RS232 Data File:
* FileName = C:\Users\Jefrey\Documents\WHOTS-18_mcat_recovery\w18_135m_6888_data.hex
* Software version SeatermV2 2.8.0.119
* Temperature SN = 6888
* Conductivity SN = 6888
* System UpLoad Time = Jun 21 2023 08:27:22
* sample interval = 75 seconds
* <ApplicationData>
* <Seaterm232>
* <SoftwareVersion>2.8.0.119</SoftwareVersion>
* <BuildDate>07-Nov-2018</BuildDate>
* </Seaterm232>
* </ApplicationData>
* <InstrumentState>
* <HardwareData DeviceType='SBE37SM-RS232' SerialNumber='03706888'>
*
* <Manufacturer>Sea-Bird Electronics, Inc.</Manufacturer>
*
* <FirmwareVersion>3.1</FirmwareVersion>
*
* <FirmwareDate>Jan 20 2012 17:33:01</FirmwareDate>
*
* <PCBAssembly>41647</PCBAssembly>
*
* <PCBAssembly>41610B</PCBAssembly>
*
* <PCBAssembly>41611D</PCBAssembly>
*
* <MfgDate>13 Mar 2009</MfgDate>
*
* <FirmwareLoader>SBE 37 FirmwareLoader V 1.0</FirmwareLoader>
*
* <InternalSensors>
*
* <Sensor id='Temperature'>
*
* <type>temperature-1</type>
*
* <SerialNumber>03706888</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Conductivity'>
*
* <type>conductivity-1</type>
*
* <SerialNumber>03706888</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Pressure'>
*
* <type>strain-0</type>
*
* <SerialNumber>3418742</SerialNumber>
*
* </Sensor>
*
* </InternalSensors>
*
* </HardwareData>
* <StatusData DeviceType='SBE37SM-RS232' SerialNumber='03706888'>
*
* <DateTime>2023-06-21T06:52:10</DateTime>
*
* <EventSummary numEvents='1'/>
*
* <Power>
*
* <vMain> 6.93</vMain>
*
* <vLith> 3.14</vLith>
*
* </Power>
*
* <MemorySummary>
*
* <Bytes>5759175</Bytes>
*
* <Samples>383945</Samples>
*
* <SamplesFree>175295</SamplesFree>
*
* <SampleLength>15</SampleLength>
*
* </MemorySummary>
*
* <AutonomousSampling>no, stop command</AutonomousSampling>
*
* </StatusData>
* <ConfigurationData DeviceType='SBE37SM-RS232' SerialNumber='03706888'>
*
* <PressureInstalled>yes</PressureInstalled>
*
* <PumpInstalled>no</PumpInstalled>
*
* <SampleDataFormat>converted engineering alternate</SampleDataFormat>
*
* <OutputSalinity>yes</OutputSalinity>
*
* <OutputSV>no</OutputSV>
*
* <TxRealTime>no</TxRealTime>
*
* <SampleInterval>75</SampleInterval>
*
* <SyncMode>no</SyncMode>
*
* </ConfigurationData>
* <CalibrationCoefficients DeviceType='SBE37SM-RS232' SerialNumber='03706888'>
*
* <Calibration format='TEMP1' id='Temperature'>
*
* <SerialNum>03706888</SerialNum>
*
* <CalDate>19-Nov-21</CalDate>
*
* <A0>7.421835e-05</A0>
*
* <A1>2.727849e-04</A1>
*
* <A2>-2.340633e-06</A2>
*
* <A3>1.491767e-07</A3>
*
* </Calibration>
*
* <Calibration format='WBCOND0' id='Conductivity'>
*
* <SerialNum>03706888</SerialNum>
*
* <CalDate>19-Nov-21</CalDate>
*
* <G>-1.009682e+00</G>
*
* <H>1.484617e-01</H>
*
* <I>-2.695763e-04</I>
*
* <J>4.233032e-05</J>
*
* <PCOR>-9.570000e-08</PCOR>
*
* <TCOR>3.250000e-06</TCOR>
*
* <WBOTC>3.829161e-07</WBOTC>
*
* </Calibration>
*
* <Calibration format='STRAIN0' id='Pressure'>
*
* <SerialNum>3418742</SerialNum>
*
* <CalDate>02-Nov-21</CalDate>
*
* <PA0>1.014290e-01</PA0>
*
* <PA1>4.977376e-03</PA1>
*
* <PA2>-2.425301e-11</PA2>
*
* <PTCA0>5.244692e+05</PTCA0>
*
* <PTCA1>2.221365e+00</PTCA1>
*
* <PTCA2>-5.610904e-02</PTCA2>
*
* <PTCB0>2.523738e+01</PTCB0>
*
* <PTCB1>4.750000e-04</PTCB1>
*
* <PTCB2>0.000000e+00</PTCB2>
*
* <PTEMPA0>-7.037432e+01</PTEMPA0>
*
* <PTEMPA1>5.113173e-02</PTEMPA1>
*
* <PTEMPA2>-6.041479e-07</PTEMPA2>
*
* <POFFSET>0.000000e+00</POFFSET>
*
* <PRANGE>1.450000e+03</PRANGE>
*
* </Calibration>
*
* </CalibrationCoefficients>
* <EventCounters DeviceType='SBE37SM-RS232' SerialNumber='03706888'>
*
* <EventSummary numEvents='1'/>
*
* <Event type='PON reset' count='1'/>
*
* </EventCounters></InstrumentState>
* <UserHeaderInsert>
* <![CDATA[
** WHOTS18 WHOTS18
** 55m 135m
* ]]>
* </UserHeaderInsert>
# nquan = 5
# nvalues = 383945
# units = specified
# name 0 = cond0S/m: Conductivity [S/m]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = prdM: Pressure, Strain Gauge [db]
# name 3 = timeJV2: Time, Instrument [julian days]
# name 4 = flag: 0.000e+00
# span 0 = -0.000154, 5.418553
# span 1 = 0.6243, 29.5186
# span 2 = -0.512, 138.892
# span 3 = 204.000000, 537.284722
# span 4 = 0.0000e+00, 0.0000e+00
# interval = seconds: 75
# start_time = Jul 23 2022 00:00:00 [Instrument's time stamp, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="3" >
# <sensor Channel="1" >
# <!-- Count, Temperature -->
# <TemperatureSensor SensorID="58" >
# <SerialNumber>6888</SerialNumber>
# <CalibrationDate>19-Nov-21</CalibrationDate>
# <A0>7.42183500e-005</A0>
# <A1>2.72784900e-004</A1>
# <A2>-2.34063300e-006</A2>
# <A3>1.49176700e-007</A3>
# <Slope>1.00000000</Slope>
# <Offset>0.0000</Offset>
# </TemperatureSensor>
# </sensor>
# <sensor Channel="2" >
# <!-- Frequency 0, Conductivity -->
# <ConductivitySensor SensorID="3" >
# <SerialNumber>6888</SerialNumber>
# <CalibrationDate>19-Nov-21</CalibrationDate>
# <UseG_J>1</UseG_J>
# <!-- Cell const and series R are applicable only for wide range sensors. -->
# <SeriesR>0.0000</SeriesR>
# <CellConst>2000.0000</CellConst>
# <ConductivityType>1</ConductivityType>
# <Coefficients equation="0" >
# <A>0.00000000e+000</A>
# <B>0.00000000e+000</B>
# <C>0.00000000e+000</C>
# <D>0.00000000e+000</D>
# <M>0.0</M>
# <CPcor>-9.57000000e-008</CPcor>
# </Coefficients>
# <Coefficients equation="1" >
# <G>-1.00968200e+000</G>
# <H>1.48461700e-001</H>
# <I>-2.69576300e-004</I>
# <J>4.23303200e-005</J>
# <CPcor>-9.57000000e-008</CPcor>
# <CTcor>3.2500e-006</CTcor>
# <!-- WBOTC not applicable unless ConductivityType = 1. -->
# <WBOTC>3.82916100e-007</WBOTC>
# </Coefficients>
# <Slope>1.00000000</Slope>
# <Offset>0.00000</Offset>
# </ConductivitySensor>
# </sensor>
# <sensor Channel="3" >
# <!-- Count, Pressure, Strain Gauge -->
# <PressureSensor SensorID="46" >
# <SerialNumber>3418742</SerialNumber>
# <CalibrationDate>02-Nov-21</CalibrationDate>
# <PA0>1.01429000e-001</PA0>
# <PA1>4.97737600e-003</PA1>
# <PA2>-2.42530100e-011</PA2>
# <PTEMPA0>-7.03743200e+001</PTEMPA0>
# <PTEMPA1>5.11317300e-002</PTEMPA1>
# <PTEMPA2>-6.04147900e-007</PTEMPA2>
# <PTCA0>5.24469200e+005</PTCA0>
# <PTCA1>2.22136500e+000</PTCA1>
# <PTCA2>-5.61090400e-002</PTCA2>
# <PTCB0>2.52373800e+001</PTCB0>
# <PTCB1>4.75000000e-004</PTCB1>
# <PTCB2>0.00000000e+000</PTCB2>
# <Offset>0.000000</Offset>
# </PressureSensor>
# </sensor>
# </Sensors>
# datcnv_date = Jun 22 2023 14:35:39, 7.26.7.129 [datcnv_vars = 4]
# datcnv_in = C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_135m_6888_data.hex C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_135m_6888_data.xmlcon
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 6891
* Sea-Bird SBE37SM-RS232 Data File:
* FileName = C:\Users\Jefrey\Documents\WHOTS-18_mcat_recovery\w18_155m_6891_data.hex
* Software version SeatermV2 2.8.0.119
* Temperature SN = 6891
* Conductivity SN = 6891
* System UpLoad Time = Jun 21 2023 11:17:45
* sample interval = 75 seconds
* <ApplicationData>
* <Seaterm232>
* <SoftwareVersion>2.8.0.119</SoftwareVersion>
* <BuildDate>07-Nov-2018</BuildDate>
* </Seaterm232>
* </ApplicationData>
* <InstrumentState>
* <HardwareData DeviceType='SBE37SM-RS232' SerialNumber='03706891'>
*
* <Manufacturer>Sea-Bird Electronics, Inc.</Manufacturer>
*
* <FirmwareVersion>3.1</FirmwareVersion>
*
* <FirmwareDate>Jan 20 2012 17:33:01</FirmwareDate>
*
* <PCBAssembly>41647</PCBAssembly>
*
* <PCBAssembly>41610B</PCBAssembly>
*
* <PCBAssembly>41611D</PCBAssembly>
*
* <MfgDate>16 Mar 2009</MfgDate>
*
* <FirmwareLoader>SBE 37 FirmwareLoader V 1.0</FirmwareLoader>
*
* <InternalSensors>
*
* <Sensor id='Temperature'>
*
* <type>temperature-1</type>
*
* <SerialNumber>03706891</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Conductivity'>
*
* <type>conductivity-1</type>
*
* <SerialNumber>03706891</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Pressure'>
*
* <type>strain-0</type>
*
* <SerialNumber>2651323</SerialNumber>
*
* </Sensor>
*
* </InternalSensors>
*
* </HardwareData>
* <StatusData DeviceType='SBE37SM-RS232' SerialNumber='03706891'>
*
* <DateTime>2023-06-21T08:45:05</DateTime>
*
* <EventSummary numEvents='1'/>
*
* <Power>
*
* <vMain> 6.94</vMain>
*
* <vLith> 3.16</vLith>
*
* </Power>
*
* <MemorySummary>
*
* <Bytes>5760540</Bytes>
*
* <Samples>384036</Samples>
*
* <SamplesFree>175204</SamplesFree>
*
* <SampleLength>15</SampleLength>
*
* </MemorySummary>
*
* <AutonomousSampling>no, stop command</AutonomousSampling>
*
* </StatusData>
* <ConfigurationData DeviceType='SBE37SM-RS232' SerialNumber='03706891'>
*
* <PressureInstalled>yes</PressureInstalled>
*
* <PumpInstalled>no</PumpInstalled>
*
* <SampleDataFormat>converted engineering alternate</SampleDataFormat>
*
* <OutputSalinity>yes</OutputSalinity>
*
* <OutputSV>no</OutputSV>
*
* <TxRealTime>no</TxRealTime>
*
* <SampleInterval>75</SampleInterval>
*
* <SyncMode>no</SyncMode>
*
* </ConfigurationData>
* <CalibrationCoefficients DeviceType='SBE37SM-RS232' SerialNumber='03706891'>
*
* <Calibration format='TEMP1' id='Temperature'>
*
* <SerialNum>03706891</SerialNum>
*
* <CalDate>19-Nov-21</CalDate>
*
* <A0>5.630907e-05</A0>
*
* <A1>2.748230e-04</A1>
*
* <A2>-2.508233e-06</A2>
*
* <A3>1.532169e-07</A3>
*
* </Calibration>
*
* <Calibration format='WBCOND0' id='Conductivity'>
*
* <SerialNum>03706891</SerialNum>
*
* <CalDate>19-Nov-21</CalDate>
*
* <G>-1.009419e+00</G>
*
* <H>1.496878e-01</H>
*
* <I>-2.838778e-04</I>
*
* <J>4.451645e-05</J>
*
* <PCOR>-9.570000e-08</PCOR>
*
* <TCOR>3.250000e-06</TCOR>
*
* <WBOTC>3.524720e-07</WBOTC>
*
* </Calibration>
*
* <Calibration format='STRAIN0' id='Pressure'>
*
* <SerialNum>2651323</SerialNum>
*
* <CalDate>02-Nov-21</CalDate>
*
* <PA0>2.339704e-01</PA0>
*
* <PA1>5.063485e-03</PA1>
*
* <PA2>-2.256721e-11</PA2>
*
* <PTCA0>5.250761e+05</PTCA0>
*
* <PTCA1>5.206896e+00</PTCA1>
*
* <PTCA2>-1.317569e-01</PTCA2>
*
* <PTCB0>2.632875e+01</PTCB0>
*
* <PTCB1>9.500000e-04</PTCB1>
*
* <PTCB2>0.000000e+00</PTCB2>
*
* <PTEMPA0>-7.163238e+01</PTEMPA0>
*
* <PTEMPA1>4.963964e-02</PTEMPA1>
*
* <PTEMPA2>-3.160714e-07</PTEMPA2>
*
* <POFFSET>4.000000e-02</POFFSET>
*
* <PRANGE>1.450000e+03</PRANGE>
*
* </Calibration>
*
* </CalibrationCoefficients>
* <EventCounters DeviceType='SBE37SM-RS232' SerialNumber='03706891'>
*
* <EventSummary numEvents='1'/>
*
* <Event type='PON reset' count='1'/>
*
* </EventCounters></InstrumentState>
* <UserHeaderInsert>
* <![CDATA[
** WHOTS18 WHOTS18
** 55m 155m
* ]]>
* </UserHeaderInsert>
# nquan = 5
# nvalues = 384036
# units = specified
# name 0 = cond0S/m: Conductivity [S/m]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = prdM: Pressure, Strain Gauge [db]
# name 3 = timeJV2: Time, Instrument [julian days]
# name 4 = flag: 0.000e+00
# span 0 = -0.000025, 5.424074
# span 1 = 0.1399, 29.5262
# span 2 = -0.194, 158.681
# span 3 = 204.000000, 537.363715
# span 4 = 0.0000e+00, 0.0000e+00
# interval = seconds: 75
# start_time = Jul 23 2022 00:00:00 [Instrument's time stamp, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="3" >
# <sensor Channel="1" >
# <!-- Count, Temperature -->
# <TemperatureSensor SensorID="58" >
# <SerialNumber>6891</SerialNumber>
# <CalibrationDate>19-Nov-21</CalibrationDate>
# <A0>5.63090700e-005</A0>
# <A1>2.74823000e-004</A1>
# <A2>-2.50823300e-006</A2>
# <A3>1.53216900e-007</A3>
# <Slope>1.00000000</Slope>
# <Offset>0.0000</Offset>
# </TemperatureSensor>
# </sensor>
# <sensor Channel="2" >
# <!-- Frequency 0, Conductivity -->
# <ConductivitySensor SensorID="3" >
# <SerialNumber>6891</SerialNumber>
# <CalibrationDate>19-Nov-21</CalibrationDate>
# <UseG_J>1</UseG_J>
# <!-- Cell const and series R are applicable only for wide range sensors. -->
# <SeriesR>0.0000</SeriesR>
# <CellConst>2000.0000</CellConst>
# <ConductivityType>1</ConductivityType>
# <Coefficients equation="0" >
# <A>0.00000000e+000</A>
# <B>0.00000000e+000</B>
# <C>0.00000000e+000</C>
# <D>0.00000000e+000</D>
# <M>0.0</M>
# <CPcor>-9.57000000e-008</CPcor>
# </Coefficients>
# <Coefficients equation="1" >
# <G>-1.00941900e+000</G>
# <H>1.49687800e-001</H>
# <I>-2.83877800e-004</I>
# <J>4.45164500e-005</J>
# <CPcor>-9.57000000e-008</CPcor>
# <CTcor>3.2500e-006</CTcor>
# <!-- WBOTC not applicable unless ConductivityType = 1. -->
# <WBOTC>3.52472000e-007</WBOTC>
# </Coefficients>
# <Slope>1.00000000</Slope>
# <Offset>0.00000</Offset>
# </ConductivitySensor>
# </sensor>
# <sensor Channel="3" >
# <!-- Count, Pressure, Strain Gauge -->
# <PressureSensor SensorID="46" >
# <SerialNumber>2651323</SerialNumber>
# <CalibrationDate>02-Nov-21</CalibrationDate>
# <PA0>2.33970400e-001</PA0>
# <PA1>5.06348500e-003</PA1>
# <PA2>-2.25672100e-011</PA2>
# <PTEMPA0>-7.16323800e+001</PTEMPA0>
# <PTEMPA1>4.96396400e-002</PTEMPA1>
# <PTEMPA2>-3.16071400e-007</PTEMPA2>
# <PTCA0>5.25076100e+005</PTCA0>
# <PTCA1>5.20689600e+000</PTCA1>
# <PTCA2>-1.31756900e-001</PTCA2>
# <PTCB0>2.63287500e+001</PTCB0>
# <PTCB1>9.50000000e-004</PTCB1>
# <PTCB2>0.00000000e+000</PTCB2>
# <Offset>0.000000</Offset>
# </PressureSensor>
# </sensor>
# </Sensors>
# datcnv_date = Jun 22 2023 14:35:00, 7.26.7.129 [datcnv_vars = 4]
# datcnv_in = C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_155m_6891_data.hex C:\Users\santi\Documents\Work\whots\whots18_mooring\mcat_data\w18_155m_6891_data.xmlcon
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 11391
* Sea-Bird SBE37SM-RS232 Data File:
* FileName = C:\Users\Rtgra\Documents\Buoy Systems\ORS\WHOTS\W18\DATA\SUBSURFACE\SBE37_11391_DEEPTEMP.hex
* Software version SeatermV2 2.8.0.119
* Temperature SN = 11391
* Conductivity SN = 11391
* System UpLoad Time = Jun 21 2023 18:58:34
* sample interval = 300 seconds
* <ApplicationData>
* <Seaterm232>
* <SoftwareVersion>2.8.0.119</SoftwareVersion>
* <BuildDate>07-Nov-2018</BuildDate>
* </Seaterm232>
* </ApplicationData>
* <InstrumentState>
* <HardwareData DeviceType='SBE37SM-RS232' SerialNumber='03711391'>
*
* <Manufacturer>Sea-Bird Electronics, Inc.</Manufacturer>
*
* <FirmwareVersion>3.1</FirmwareVersion>
*
* <FirmwareDate>Jan 20 2012 17:33:01</FirmwareDate>
*
* <PCBAssembly>41647.1</PCBAssembly>
*
* <PCBAssembly>41610B</PCBAssembly>
*
* <PCBAssembly>41611D</PCBAssembly>
*
* <MfgDate>14-Nov-2013</MfgDate>
*
* <FirmwareLoader>SBE 37 FirmwareLoader V 1.0</FirmwareLoader>
*
* <InternalSensors>
*
* <Sensor id='Temperature'>
*
* <type>temperature-1</type>
*
* <SerialNumber>03711391</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Conductivity'>
*
* <type>conductivity-1</type>
*
* <SerialNumber>03711391</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Pressure'>
*
* <type>strain-0</type>
*
* <SerialNumber>2146837</SerialNumber>
*
* </Sensor>
*
* </InternalSensors>
*
* </HardwareData>
* <StatusData DeviceType='SBE37SM-RS232' SerialNumber='03711391'>
*
* <DateTime>2023-06-21T18:34:35</DateTime>
*
* <EventSummary numEvents='1'/>
*
* <Power>
*
* <vMain> 6.94</vMain>
*
* <vLith> 3.25</vLith>
*
* </Power>
*
* <MemorySummary>
*
* <Bytes>1441905</Bytes>
*
* <Samples>96127</Samples>
*
* <SamplesFree>463113</SamplesFree>
*
* <SampleLength>15</SampleLength>
*
* </MemorySummary>
*
* <AutonomousSampling>no, stop command</AutonomousSampling>
*
* </StatusData>
* <ConfigurationData DeviceType='SBE37SM-RS232' SerialNumber='03711391'>
*
* <PressureInstalled>yes</PressureInstalled>
*
* <PumpInstalled>no</PumpInstalled>
*
* <SampleDataFormat>converted engineering</SampleDataFormat>
*
* <OutputSalinity>no</OutputSalinity>
*
* <OutputSV>no</OutputSV>
*
* <TxRealTime>yes</TxRealTime>
*
* <SampleInterval>300</SampleInterval>
*
* <SyncMode>no</SyncMode>
*
* </ConfigurationData>
* <CalibrationCoefficients DeviceType='SBE37SM-RS232' SerialNumber='03711391'>
*
* <Calibration format='TEMP1' id='Temperature'>
*
* <SerialNum>03711391</SerialNum>
*
* <CalDate>10-Mar-22</CalDate>
*
* <A0>-8.177573e-05</A0>
*
* <A1>3.039413e-04</A1>
*
* <A2>-4.298826e-06</A2>
*
* <A3>1.961128e-07</A3>
*
* </Calibration>
*
* <Calibration format='WBCOND0' id='Conductivity'>
*
* <SerialNum>03711391</SerialNum>
*
* <CalDate>10-Mar-22</CalDate>
*
* <G>-9.952020e-01</G>
*
* <H>1.383237e-01</H>
*
* <I>-1.641585e-04</I>
*
* <J>3.163423e-05</J>
*
* <PCOR>-9.570000e-08</PCOR>
*
* <TCOR>3.250000e-06</TCOR>
*
* <WBOTC>1.459091e-06</WBOTC>
*
* </Calibration>
*
* <Calibration format='STRAIN0' id='Pressure'>
*
* <SerialNum>2146837</SerialNum>
*
* <CalDate>08-Mar-22</CalDate>
*
* <PA0>-2.378486e+01</PA0>
*
* <PA1>3.123519e-02</PA1>
*
* <PA2>2.005387e-09</PA2>
*
* <PTCA0>5.227441e+05</PTCA0>
*
* <PTCA1>-3.392557e+01</PTCA1>
*
* <PTCA2>8.374315e-02</PTCA2>
*
* <PTCB0>9.968137e+01</PTCB0>
*
* <PTCB1>-8.810519e-03</PTCB1>
*
* <PTCB2>0.000000e+00</PTCB2>
*
* <PTEMPA0>-9.517107e+01</PTEMPA0>
*
* <PTEMPA1>3.984701e-02</PTEMPA1>
*
* <PTEMPA2>1.262323e-06</PTEMPA2>
*
* <POFFSET>0.000000e+00</POFFSET>
*
* <PRANGE>1.015300e+04</PRANGE>
*
* </Calibration>
*
* </CalibrationCoefficients>
* <EventCounters DeviceType='SBE37SM-RS232' SerialNumber='03711391'>
*
* <EventSummary numEvents='1'/>
*
* <Event type='PON reset' count='1'/>
*
* </EventCounters></InstrumentState>
# nquan = 6
# nvalues = 96127
# units = specified
# name 0 = cond0S/m: Conductivity [S/m]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = timeJV2: Time, Instrument [julian days]
# name 3 = sal00: Salinity, Practical [PSU]
# name 4 = prdM: Pressure, Strain Gauge [db]
# name 5 = flag: 0.000e+00
# span 0 = 0.000043, 5.446433
# span 1 = 1.4674, 36.8171
# span 2 = 204.000000, 537.770833
# span 3 = 0.0088, 35.2750
# span 4 = -0.424, 4784.020
# span 5 = 0.0000e+00, 0.0000e+00
# interval = seconds: 300
# start_time = Jul 23 2022 00:00:00 [Instrument's time stamp, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="3" >
# <sensor Channel="1" >
# <!-- Count, Temperature -->
# <TemperatureSensor SensorID="58" >
# <SerialNumber>11391</SerialNumber>
# <CalibrationDate>10-Mar-22</CalibrationDate>
# <A0>-8.17757300e-005</A0>
# <A1>3.03941300e-004</A1>
# <A2>-4.29882600e-006</A2>
# <A3>1.96112800e-007</A3>
# <Slope>1.00000000</Slope>
# <Offset>0.0000</Offset>
# </TemperatureSensor>
# </sensor>
# <sensor Channel="2" >
# <!-- Frequency 0, Conductivity -->
# <ConductivitySensor SensorID="3" >
# <SerialNumber>11391</SerialNumber>
# <CalibrationDate>10-Mar-22</CalibrationDate>
# <UseG_J>1</UseG_J>
# <!-- Cell const and series R are applicable only for wide range sensors. -->
# <SeriesR>0.0000</SeriesR>
# <CellConst>2000.0000</CellConst>
# <ConductivityType>1</ConductivityType>
# <Coefficients equation="0" >
# <A>0.00000000e+000</A>
# <B>0.00000000e+000</B>
# <C>0.00000000e+000</C>
# <D>0.00000000e+000</D>
# <M>0.0</M>
# <CPcor>-9.57000000e-008</CPcor>
# </Coefficients>
# <Coefficients equation="1" >
# <G>-9.95202000e-001</G>
# <H>1.38323700e-001</H>
# <I>-1.64158500e-004</I>
# <J>3.16342300e-005</J>
# <CPcor>-9.57000000e-008</CPcor>
# <CTcor>3.2500e-006</CTcor>
# <!-- WBOTC not applicable unless ConductivityType = 1. -->
# <WBOTC>1.45909100e-006</WBOTC>
# </Coefficients>
# <Slope>1.00000000</Slope>
# <Offset>0.00000</Offset>
# </ConductivitySensor>
# </sensor>
# <sensor Channel="3" >
# <!-- Count, Pressure, Strain Gauge -->
# <PressureSensor SensorID="46" >
# <SerialNumber>2146837</SerialNumber>
# <CalibrationDate>08-Mar-22</CalibrationDate>
# <PA0>-2.37848600e+001</PA0>
# <PA1>3.12351900e-002</PA1>
# <PA2>2.00538700e-009</PA2>
# <PTEMPA0>-9.51710700e+001</PTEMPA0>
# <PTEMPA1>3.98470100e-002</PTEMPA1>
# <PTEMPA2>1.26232300e-006</PTEMPA2>
# <PTCA0>5.22744100e+005</PTCA0>
# <PTCA1>-3.39255700e+001</PTCA1>
# <PTCA2>8.37431500e-002</PTCA2>
# <PTCB0>9.96813700e+001</PTCB0>
# <PTCB1>-8.81051900e-003</PTCB1>
# <PTCB2>0.00000000e+000</PTCB2>
# <Offset>0.000000</Offset>
# </PressureSensor>
# </sensor>
# </Sensors>
# datcnv_date = Jun 21 2023 18:59:36, 7.26.7.129 [datcnv_vars = 5]
# datcnv_in = C:\Users\Rtgra\Documents\Buoy Systems\ORS\WHOTS\W18\DATA\SUBSURFACE\sbe37_11391_deeptemp.hex C:\Users\Rtgra\Documents\Buoy Systems\ORS\WHOTS\W18\DATA\SUBSURFACE\sbe37_11391_deeptemp.XMLCON
# datcnv_skipover = 0
# file_type = ascii
*END*
# Metadata for Sensor Serial Number: 12241
* Sea-Bird SBE37SM-RS232 Data File:
* FileName = C:\Users\Rtgra\Documents\Buoy Systems\ORS\WHOTS\W18\DATA\SUBSURFACE\SBE37_12241_DEEPTEMP.hex
* Software version SeatermV2 2.8.0.119
* Temperature SN = 12241
* Conductivity SN = 12241
* System UpLoad Time = Jun 21 2023 19:07:23
* sample interval = 300 seconds
* <ApplicationData>
* <Seaterm232>
* <SoftwareVersion>2.8.0.119</SoftwareVersion>
* <BuildDate>07-Nov-2018</BuildDate>
* </Seaterm232>
* </ApplicationData>
* <InstrumentState>
* <HardwareData DeviceType='SBE37SM-RS232' SerialNumber='03712241'>
*
* <Manufacturer>Sea-Bird Electronics, Inc.</Manufacturer>
*
* <FirmwareVersion>3.1</FirmwareVersion>
*
* <FirmwareDate>Jan 20 2012 17:33:01</FirmwareDate>
*
* <PCBAssembly>41647.1</PCBAssembly>
*
* <PCBAssembly>41610B</PCBAssembly>
*
* <PCBAssembly>41611D</PCBAssembly>
*
* <MfgDate> 9 MAY 2014</MfgDate>
*
* <FirmwareLoader>SBE 37 FirmwareLoader V 1.0</FirmwareLoader>
*
* <InternalSensors>
*
* <Sensor id='Temperature'>
*
* <type>temperature-1</type>
*
* <SerialNumber>03712241</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Conductivity'>
*
* <type>conductivity-1</type>
*
* <SerialNumber>03712241</SerialNumber>
*
* </Sensor>
*
* <Sensor id='Pressure'>
*
* <type>strain-0</type>
*
* <SerialNumber>2153123</SerialNumber>
*
* </Sensor>
*
* </InternalSensors>
*
* </HardwareData>
* <StatusData DeviceType='SBE37SM-RS232' SerialNumber='03712241'>
*
* <DateTime>2023-06-21T18:43:23</DateTime>
*
* <EventSummary numEvents='1'/>
*
* <Power>
*
* <vMain> 6.98</vMain>
*
* <vLith> 3.24</vLith>
*
* </Power>
*
* <MemorySummary>
*
* <Bytes>1441935</Bytes>
*
* <Samples>96129</Samples>
*
* <SamplesFree>463111</SamplesFree>
*
* <SampleLength>15</SampleLength>
*
* </MemorySummary>
*
* <AutonomousSampling>no, stop command</AutonomousSampling>
*
* </StatusData>
* <ConfigurationData DeviceType='SBE37SM-RS232' SerialNumber='03712241'>
*
* <PressureInstalled>yes</PressureInstalled>
*
* <PumpInstalled>no</PumpInstalled>
*
* <SampleDataFormat>converted engineering</SampleDataFormat>
*
* <OutputSalinity>no</OutputSalinity>
*
* <OutputSV>no</OutputSV>
*
* <TxRealTime>no</TxRealTime>
*
* <SampleInterval>300</SampleInterval>
*
* <SyncMode>no</SyncMode>
*
* </ConfigurationData>
* <CalibrationCoefficients DeviceType='SBE37SM-RS232' SerialNumber='03712241'>
*
* <Calibration format='TEMP1' id='Temperature'>
*
* <SerialNum>03712241</SerialNum>
*
* <CalDate>25-Feb-22</CalDate>
*
* <A0>-1.173750e-04</A0>
*
* <A1>3.062532e-04</A1>
*
* <A2>-4.331589e-06</A2>
*
* <A3>1.981291e-07</A3>
*
* </Calibration>
*
* <Calibration format='WBCOND0' id='Conductivity'>
*
* <SerialNum>03712241</SerialNum>
*
* <CalDate>25-Feb-22</CalDate>
*
* <G>-9.871401e-01</G>
*
* <H>1.724485e-01</H>
*
* <I>-2.191593e-04</I>
*
* <J>4.628980e-05</J>
*
* <PCOR>-9.570000e-08</PCOR>
*
* <TCOR>3.250000e-06</TCOR>
*
* <WBOTC>1.392140e-07</WBOTC>
*
* </Calibration>
*
* <Calibration format='STRAIN0' id='Pressure'>
*
* <SerialNum>2153123</SerialNum>
*
* <CalDate>16-Feb-22</CalDate>
*
* <PA0>-1.777185e+00</PA0>
*
* <PA1>3.015012e-02</PA1>
*
* <PA2>1.884953e-09</PA2>
*
* <PTCA0>5.252472e+05</PTCA0>
*
* <PTCA1>-8.637300e+00</PTCA1>
*
* <PTCA2>2.466118e-01</PTCA2>
*
* <PTCB0>1.031030e+02</PTCB0>
*
* <PTCB1>-9.453885e-03</PTCB1>
*
* <PTCB2>0.000000e+00</PTCB2>
*
* <PTEMPA0>-9.679022e+01</PTEMPA0>
*
* <PTEMPA1>4.040292e-02</PTEMPA1>
*
* <PTEMPA2>1.142765e-06</PTEMPA2>
*
* <POFFSET>0.000000e+00</POFFSET>
*
* <PRANGE>1.015300e+04</PRANGE>
*
* </Calibration>
*
* </CalibrationCoefficients>
* <EventCounters DeviceType='SBE37SM-RS232' SerialNumber='03712241'>
*
* <EventSummary numEvents='1'/>
*
* <Event type='PON reset' count='1'/>
*
* </EventCounters></InstrumentState>
# nquan = 6
# nvalues = 96129
# units = specified
# name 0 = cond0S/m: Conductivity [S/m]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = timeJV2: Time, Instrument [julian days]
# name 3 = sal00: Salinity, Practical [PSU]
# name 4 = prdM: Pressure, Strain Gauge [db]
# name 5 = flag: 0.000e+00
# span 0 = 7.8785e-07, 5.444069
# span 1 = 1.4674, 38.2886
# span 2 = 204.000000, 537.777778
# span 3 = 0.0057, 35.2606
# span 4 = -2.056, 4791.746
# span 5 = 0.0000e+00, 0.0000e+00
# interval = seconds: 300
# start_time = Jul 23 2022 00:00:00 [Instrument's time stamp, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="3" >
# <sensor Channel="1" >
# <!-- Count, Temperature -->
# <TemperatureSensor SensorID="58" >
# <SerialNumber>12241</SerialNumber>
# <CalibrationDate>25-Feb-22</CalibrationDate>
# <A0>-1.17375000e-004</A0>
# <A1>3.06253200e-004</A1>
# <A2>-4.33158900e-006</A2>
# <A3>1.98129100e-007</A3>
# <Slope>1.00000000</Slope>
# <Offset>0.0000</Offset>
# </TemperatureSensor>
# </sensor>
# <sensor Channel="2" >
# <!-- Frequency 0, Conductivity -->
# <ConductivitySensor SensorID="3" >
# <SerialNumber>12241</SerialNumber>
# <CalibrationDate>25-Feb-22</CalibrationDate>
# <UseG_J>1</UseG_J>
# <!-- Cell const and series R are applicable only for wide range sensors. -->
# <SeriesR>0.0000</SeriesR>
# <CellConst>2000.0000</CellConst>
# <ConductivityType>1</ConductivityType>
# <Coefficients equation="0" >
# <A>0.00000000e+000</A>
# <B>0.00000000e+000</B>
# <C>0.00000000e+000</C>
# <D>0.00000000e+000</D>
# <M>0.0</M>
# <CPcor>-9.57000000e-008</CPcor>
# </Coefficients>
# <Coefficients equation="1" >
# <G>-9.87140100e-001</G>
# <H>1.72448500e-001</H>
# <I>-2.19159300e-004</I>
# <J>4.62898000e-005</J>
# <CPcor>-9.57000000e-008</CPcor>
# <CTcor>3.2500e-006</CTcor>
# <!-- WBOTC not applicable unless ConductivityType = 1. -->
# <WBOTC>1.39214000e-007</WBOTC>
# </Coefficients>
# <Slope>1.00000000</Slope>
# <Offset>0.00000</Offset>
# </ConductivitySensor>
# </sensor>
# <sensor Channel="3" >
# <!-- Count, Pressure, Strain Gauge -->
# <PressureSensor SensorID="46" >
# <SerialNumber>2153123</SerialNumber>
# <CalibrationDate>16-Feb-22</CalibrationDate>
# <PA0>-1.77718500e+000</PA0>
# <PA1>3.01501200e-002</PA1>
# <PA2>1.88495300e-009</PA2>
# <PTEMPA0>-9.67902200e+001</PTEMPA0>
# <PTEMPA1>4.04029200e-002</PTEMPA1>
# <PTEMPA2>1.14276500e-006</PTEMPA2>
# <PTCA0>5.25247200e+005</PTCA0>
# <PTCA1>-8.63730000e+000</PTCA1>
# <PTCA2>2.46611800e-001</PTCA2>
# <PTCB0>1.03103000e+002</PTCB0>
# <PTCB1>-9.45388500e-003</PTCB1>
# <PTCB2>0.00000000e+000</PTCB2>
# <Offset>0.000000</Offset>
# </PressureSensor>
# </sensor>
# </Sensors>
# datcnv_date = Jun 21 2023 19:07:27, 7.26.7.129 [datcnv_vars = 5]
# datcnv_in = C:\Users\Rtgra\Documents\Buoy Systems\ORS\WHOTS\W18\DATA\SUBSURFACE\sbe37_12241_deeptemp.hex C:\Users\Rtgra\Documents\Buoy Systems\ORS\WHOTS\W18\DATA\SUBSURFACE\sbe37_12241_deeptemp.XMLCON
# datcnv_skipover = 0
# file_type = ascii
*END*